Coconut Oak Mohawk RevWood Miramar Shores Laminate

Dimensions: 15/32" x 8 11/32" x 54 11/32"
Construction: Plank
Design: Laminate
Coverage: 22.04/SQ.FT
Edge Style: GenuEdge
Finish: CleanProtect
Install Method: Uniclic® Floating
Warranty: Lifetime Residential
Certification: FloorScore

InstaForm Transition
Mono-Trak
Overlap Stair Nose
Quarter Round
RealSound Underlayment
Install Kit

Mohawk Revwood Installation Instructions

Site Requirements
RevWood Plus™ is a durable floor covering, not intended as structural material. RevWood Plus requires a clean, dry, secure subfloor that meets building codes. The following requirements are not intended to supersede federal, state or local building codes, but as with many other interior finish products, may require modifying existing structural components for successful installation. Owner assumes responsibilityIt for compliance with all building codes. RevWood Plus flooring is suitable for use in climate controlled (35-65% RH and 60-85° F) indoor installations only and should not be installed in rooms with floor drains or sump pumps. RevWood Plus floor can be installed above, on or below grade. A moisture test is strongly recommended to determine if high moisture exists in the subfloor. When using a calcium chloride moisture test for concrete subfloors (ASTM F1869), values must be ≤ 5 lbs/1000ft²/24-hr or <80% RH with an in situ probe (ASTM F2170). Moisture readings of wood subfloors must be ≤ 12%.
Acceptable job site conditions, including relative humidity and subfloor moisture conditions, must be maintained throughout the lifetime of the flooring. RevWood Plus flooring is installed as a floating floor and requires the use of T-moldings in doorways less than 32-inches (0.81m) or if the installation changes directions through the doorway (regardless of doorway size) and in rooms 50 feet ( 15,24m) or larger in length or width. Floor movement must not be constrained by glue, nails, screws, hardware or other fixed obstructions.
*This product must be installed in accordance with installation instructions illustrated in pages 3-4.
Site and Material Preparation
A. Remove carpet and padding. Also remove any wood flooring installed on concrete. Do not remove products unless they are asbestos-free.
B. Undercut door frame and wallbase. Slide the flooring at least 1/4" underneath the door frame and wallbase. Also leave a concealed 3/8" minimum expansion space under each.
C. Remove bumps or peaks in subfloor and fill depressions with floor leveling compound to ensure no more than 3/16” unevenness per 10 foot span.
D. Acclimate unopened product before installation. If there is no time for acclimation, there should be no more than a difference of 25° F and
20% relative humidity between the stocking/transportation environment of the flooring and the final installation environment of the flooring. E. Clean debris from subfloor before installation.
F. For concrete subfloors, install vapor barrier with overlapped seams of 8" or more.
G. For planks without attached underlayment, install over single layer of underlayment appropriate for RevWood Plus floors.
Flooring Installation
1. Inspect each plank. Floor should be installed blending planks from several cartons at the same time to ensure good color and shade mixture throughout the installation.
2. For the first row along straight walls, remove the tongue on all long side joints and on the short side of the first plank only.
3. For uneven walls, trace contour on tongue side of plank and cut.
4. Assemble the first row tongue side toward wall. Insert the end tongue into the end groove and rotate downward to assemble. Keep the planks aligned and the joints closed.
5. Two spacers thick side to thick side equals 3/8".
6. Provide a 3/8" space for expansion on all sides. First piece must be at least 8" long. Start new rows with pieces trimmed from previous row. Ensure at least a 6" end joint offset.
7. At a slight angle, insert the tongue of plank 2 into the groove of plank 1 until the RevWood Plus edges meet, and then rotate down until the joints lock.
8. Join the short end of the plank first. There will be a gap on the long side joints when the plank is rotated down.
9. Raise the outside edge of the plank upward approximately 1". Maintain this angle as you push the plank in until the RevWood Plus edges meet. Rotate downward on the plank until the joint locks. Repeat these steps to complete the installation.
Installation Tip: Place a carton of planks across the end of the row being installed to keep installed planks in place during installation.
10. Alternate Tap Method: Align the tongues into the grooves of the long and short sides of the planks. Install the long side first with a tapping block by tapping lightly along the long side until the joint is closed tightly. Then tap the end using the tapping block into a locked position. Note: Uneven tapping or use of excessive force may damage the joint.
11. Ensure there will be a 3/8" gap (after the joint is closed) to the wall for expansion.
12. For the last row, align the plank to be used on top of the second to last row. Using a full width plank as a spacer, trace wall contour and cut plank.
13. For the last row, install the long side tongue into the groove with the end joint aligned. Using a pull bar and hammer, work evenly along the length of the plank and lightly tap the joint closed.
14. After tapping the long side joint closed, tap the short side closed, using a tapping block or a pull bar.
Installation Under Doorway Frames
15. Slide plank under pre-cut door frame.
16. Tap the long side joint closed first. Then tap the end joint closed.
Installation Around Fixed Objects (Such as Pipes)
17. Allow 3/8" expansion space around pipes or other fixed objects.
Finishing the Installation
18. Remove all spacers.
19. Create a watertight seal by applying flexible 100% silicone sealant to the entire perimeter of the installation. DO NOT use acrylic sealant.
• First fill all expansion spaces with 3/8" compressible PE foam backer rod and cover with silicone sealant.
• Prior to installing the moldings, apply silicone sealant to the portion of the molding or transition that will contact directly with the RevWood Plus flooring surface.
• Install moldings and immediately wipe away any excess silicone sealant.
• Apply silicone sealant at connections to doorframes or any other fixed objects

MOHAWK WOOD PRODCUTS LIMITED WARRANTY
This brochure contains details of all the warranties featured on our wood flooring products. However, not all warranties apply to all products. The specific warranties applicable to each individual product line are designated on the samples featured by the authorized retailer at the time of the flooring purchase.
Please keep these important papers regarding your flooring on hand for future reference:
• This brochure
• Original receipt
Retaining these documents ensures that you’ll have all the necessary paperwork handy in the unlikely event of a warranty claim. Mohawk also recommends keeping excess planks from your installation for your warranty and in case you ever need to make a repair.

LIMITED WARRANTIES

Manufacturing Defect Warranty
All TecWood, UltraWood, and RevWood Products
Mohawk warrants to the original buyer that the flooring will be free of defects in material and/or workmanship in accordance with the terms of this warranty for as long as the buyer owns the home.
Terms and Conditions
• This limited warranty only covers the flooring under normal residential use when Mohawk installation and maintenance instructions are followed properly.
• This warranty only applies to inherent defects that were not visible before or during the installation of the flooring.
• Flooring planks or accessories must be checked carefully for material defects before and during installation under sufficient lighting. Installation indicates acceptance of quality.
Exclusions
• These limited warranties do not cover damage to the flooring that occurs during shipment or installation.
• Installation of flooring that contains any obvious or visible manufacturing defect is not covered by these limited warranties.
• Color and gloss differences resulting from material added to an existing installation at a later date or from non-warranty repairs are excluded from coverage.
• These limited warranties do not apply to flooring that has been subjected to abnormal use or conditions or abused in any way, which includes but is not limited to moisture damage from plumbing, storms or flooding; damage from smoke, fire or other casualty events; damage caused by negligence; improper alterations of the original manufactured product; damage from use of the flooring that is unreasonable considering the normal and expected uses of flooring in a residential environment; or damage of mechanical nature.
Wear Resistance Warranty
All TecWood, UltraWood, and RevWood Products
As a result of normal use, the protective layer will not wear through to the wood veneer or decorative layer.
Terms and Conditions
• Gloss change is not considered surface wear.
• In beveled-edge products, this wear resistance warranty does not include wear along the edges of the planks less than 3/16” (5 mm) from the edge.
• Refinishing the flooring voids the wear resistance warranty.
• Wear of the hardwood or design layer must be readily visible, covering at least one square inch.
• Chair pads or mats must be used under caster chairs.
General Stain Warranty
All TecWood, UltraWood, and RevWood Products
Mohawk warrants to the original buyer that the flooring will not stain under normal household use for the specified duration.
Terms and Conditions
• This warranty does not apply to stains as a result of chemical or industrial products other than recommended cleaning products.
• This warranty excludes pet stains.
Fade Resistance Warranty
All RevWood Products
The flooring will not fade from exposure to sunlight or artificial light for the specified duration.
Hardwood Structure Lifetime Warranty
All TecWood and UltraWood Products
Mohawk warrants that the flooring will resist ply separation for the specified duration under normal residential use when properly installed and maintained in accordance with Mohawk instructions. Terms and Conditions
• Mohawk products are not warranted against squeaking, popping, or crackling
• Hardwood is a natural product and may exhibit naturally occurring variations in grain and color, mineral streaks and knots. The installer must use reasonable selectivity and hold out or cut off objectionable blemishes prior to installation.

Wet Warranty

Wet Resistance Warranty
All TecWood and RevWood Essentials Products
Flooring will resist damage from normal topical household spills under normal use for the specified duration. Terms and Conditions
• Do not allow topical moisture to remain on the floor longer than 30 minutes.
• Topical spills allowed to remain on the floor longer than 30 minutes may damage the flooring and void this warranty.
• Damp mop only. The flooring is not designed for wet or steam mopping.
• Damage from pet urine is not covered by this warranty.
• See General Wet Warranty Terms and Conditions for additional information regarding this Wet Resistance Warranty.
Waterproof Warranty
RevWood Select Products
The flooring system will resist damage from normal topical and household spills and domestic household pet accidents under normal use for the specified duration. The flooring will also withstand moisture from damp or wet mopping. Terms and Conditions
• Damp or wet mop only. The flooring is not designed for steam mopping.
• See General Wet Warranty Terms and Conditions for additional information regarding this Waterproof Flooring System Warranty.
WetProtect Warranty
All UltraWood, RevWood Plus, and RevWood Premier Products WetProtect is a no-exclusions wet warranty that covers damage from all common household spills, domestic household pet accidents, damp and wet mopping. In addition, the coverage includes damage to both the flooring and subfloor from topical moisture for the life of the product.
Terms and Conditions
• Subfloor damage is defined as visible damage to the surface of a concrete or wood subfloor, including mold or mildew growth, rot or decay caused by topical moisture leaking through the joint system.
• In all cases, subfloor damage must be the result of topical moisture leaking through a properly installed joint.
• See General Wet Warranty Terms and Conditions for additional information regarding this WetProtect Warranty.
Steam Mop Warranty
All UltraWood, RevWood Plus, and RevWood Premier Products A residential steam mop may be used, provided the steam is applied to a microfiber pad and not applied directly to the floor.
• Make sure to set the temperature of the steam mop to the appropriate setting for wood floors, or to the lowest setting.
• Steam mop in the length direction of the planks only.
General Wet Warranty Terms and Conditions
Unless otherwise specified, topical spills refer to normal household substances. All spills should be removed promptly using a clean dry or damp cloth. If additional cleaning is necessary, use Mohawk recommended products and a microfiber cloth.
• These warranties are contingent on proper care and maintenance. Please refer to Mohawk’s Care and Maintenance section for full instructions.
• These warranties are contingent on proper installation. Please refer to Mohawk’s Installation Guide for full instructions.
• Complete waterproof coverage requires the perimeter of the floor to be sealed in accordance with the products installation instructions. Waterproof and WetProtect warranties do not apply to damage at an unsealed perimeter, including but not limited to: leaks, spills, pet urine, wet mopping, or steam mopping.
• If you choose to forego perimeter sealing and damage occurs in areas of the floor unassociated with the unsealed perimeter, the damage will remain fully covered by the Waterproof and WetProtect warranties.
• Complete waterproof coverage requires a perimeter seal in accordance with the applicable product’s installation instructions. Mohawk strongly recommends a professionally installed perimeter seal. If the original owner or installer chooses to forgo perimeter sealing, waterproof coverage is impacted and limited. In the event of water or moisture damage related to moisture contact on an unprotected area due to failure to properly seal the perimeter (including but not limited to leaks, spills, wet mopping, or steam mopping), the coverage will not apply. This does not impact water damage unrelated to failure to perimeter seal.
• The flooring is not designed to withstand flooding, acts of God, plumbing accidents or leaking appliances (icemakers, dishwashers, clothes washers, etc.). These and other casualty events are not considered topical spills.
• The flooring is not designed to withstand water or moisture in the subfloor or underneath the flooring, including but not limited to damage from subfloor hydrostatic pressure (water or moisture under the floor that is transmitted to the surface through exerted pressure) or other conditions that result in water or moisture beneath the flooring.
• The flooring is not designed to withstand damage from moisture that originates from outside the room where it was installed.
• Consequential damages, including any medical issues related to mold or mildew growth, is not covered by this warranty.
• For residential warranty claims involving subfloor damage, Mohawk will cover reasonable labor costs to clean visible mold and mildew growth using industry standard methods.
• For residential claims involving wood subfloor damage, Mohawk will cover reasonable labor and materials costs to repair or replace only the damaged sections of subfloor.
• Replacement or cleaning of insulation, floor joists or other structural, mechanical or electrical components is not covered by this warranty.

Joint Integrity Warranty
All UltraWood and RevWood Products
The flooring joints will remain secure under normal use.
Terms and Conditions
• Responsibility under this warranty only applies to flooring defects that were not visible before or during the installation of the product.
• This warranty only applies to open joints greater than 0.015 inches (0.381 mm).
Pet Protection - Mohawk All Pet
All UltraWood, RevWood Select, RevWood Plus, RevWood
Premier Products
All Pet Stain Protection covers all pets and all accidents for the specified duration. The flooring will resist staining from vomit, urine and feces of all domestic pets. Please refer to the attached Warranty Chart for precise duration of coverage, listed by product line.
Antimicrobial* Warranty
UltraWood Plus and RevWood Premier Products
Antimicrobial protected flooring is effective against certain common
bacteria that cause stains, odors and product degradation. The antimicrobial product protection will not be removed by proper care and cleaning. Terms and Conditions
• Antimicrobial product protection is limited to the top surface of the product only.
• *Antimicrobial flooring is not designed to protect users from disease-causing bacteria.
• Mohawk disclaims liability for any sickness or death caused by microbes on the flooring surface or any associated medical or other expenses.
• In the event of a warranty claim, Mohawk may inspect the product and determine the extent to which the protection has been diminished.

Care and Cleaning
Place felt floor protectors under legs of moveable furniture. Chair casters should be rubber – not plastic or metal. Place walk-off mats at entrances. Dust mop as primary cleaning method. Occasionally wet mop with water only, using a well wrung out mop; DO NOT pour liquid directly on floor or use an excessively wet mop that will puddle or leave moisture standing on the floor. If needed, use a solution of 1 cup of vinegar per gallon of water OR 1/3 cup non-sudsing ammonia per gallon of water. DO NOT use detergents, abrasive cleaners, soaps, waxes or polishes. Use correct hard surface vacuum tools. DO NOT use rotating beater bars, floor scrubbers, jet mops, buffers or similar products. Wipe up spills immediately. DO NOT allow topical moisture to remain on the floor longer than the time specified in the product warranty.