Dusk Casabella ScubaTech Laminate

Dimensions: 12mm x 6 9/16" x 48" - 20 mil Wear Layer
Construction: Plank - Attached Pad
Design: Laminate
Coverage: 22.14/SQ.FT
Edge Style: Beveled Edges And Ends
Finish: NanoTek
Install Method: Valinge 2G
Certification: FloorScore
Warranty: Lifetime Residential - 15 Year Commercial

Overlap Stair Nose
Overlap Reducer
Quarter Round
Square Nose
Scuba Thermo Silent Underlayment

Casabella® LAMINATE FLOOR INSTALLATION INSTRUCTIONS

Retailer/Installer/Owner Responsibility

Carefully inspect all Casabella Laminate flooring prior to installation for defects/objections:
Materials installed with visible defects are not covered under our warranty. This is an industry standard. Accepting or rejecting the material must be done on full cartons not plank by plank. Casabella Laminate flooring has one of the lowest warranty rates in the industry and the highest manufacturing standard in the industry. We want you to be satisfied with your purchase.

You MUST, as the final inspector, inspect for proper color, finish, style, and quality PRIOR to installation. Verify that the flooring is the correct material. Care should be taken at this time to remove or repair particular characteristics you do not desire.
IT IS YOUR RESPONSIBILITY TO INSPECT THE FLOORING BEFORE IT IS INSTALLED. IF YOU ARE NOT SATISFIED WITH THE FLOORING PRIOR TO INSTALLATION, CONTACT YOUR DEALER. DO NOT INSTALL THE FLOORING. IF YOU INSTALL THE FLOORING, YOU HAVE ACCEPTED ITS MANUFACTURED APPEARANCE.

MANUFACTURER SHALL NOT BE RESPONSIBLE FOR ANY COSTS INCURRED WHEN PLANK(S) WITH VISIBLE DEFECTS HAVE BEEN INSTALLED. A VISIBLE DEFECT IS ANY DEFECT THAT EXISTS BEFORE INSTALLATION AND WAS VISIBLE TO THE NAKED EYE. IF YOUR LAMINATE FLOORING IS INSTALLED PROPERLY AND NOT DAMAGED BY EXCLUSIONS NOT COVERED BY OUR WARRANTY, CASABELLA LAMINATE, WILL ALWAYS WARRANTY THE STRUCTURE OF YOUR FLOORING AS PER THE WARRANTY AGREEMENT.

The use of stain, filler, or putty stick for the correction of minor defects during installation should be accepted as normal procedure.

An 8% cutting allowance, depending on layout, must be added to the actual square footage amount needed. (Some installations will require a higher percentage.)

CAUTION: WOOD DUST
The International Agency for Research on Cancer has classified wood dust as a nasal carcinogen. The sawing, sanding, and/ or machining of wood products can produce wood dust that can cause respiratory, eye, and skin irritations. Equipment should be equipped with a dust collector to reduce airborne wood dust. Wear an appropriate NIOSH designated dust mask to reduce exposure to airborne wood dust. Avoid contact with eyes and skin. In case of irritation, flush eyes or skin with water for at least 15 minutes. In cases of severe irritation; seek immediate medical attention. For further technical or installation questions or to request a Product Specification Data Sheet contact the manufacturer. 1-281-766-1600
BE CAREFUL TO SELECT THE INSTALLATION THAT MATCHES THE PRODUCT YOU PURCHASED

INSTALLATION WHEN USING A LOCKING SYSTEM:

A. WHERE CAN THE FLOORING BE INSTALLED?
Install CASABELLA® LAMINATE in most rooms and most grade levels WHEN PROPER PREPARATION IS USED, AND AREA MEETS MOISTURE TEST REQUIRMENTS.


B. LAUNDRY ROOM FLOORS ARE NOT OK:
Do not install CASABELLA® LAMINATE in areas of excessive moisture or excessive humidity. Moisture damage from water dispenser that is not cleaned up timely is not covered by this warranty.
PREPARATION OF FLOOR:
Install CASABELLA® LAMINATE on concrete, ceramic tile, terrazzo, marble or stone sub-floors that are smooth, level and well bonded. CASABELLA® LAMINATE may also be installed on wood or wood product sub-floors that are clean, well bonded and smooth.
DO NOT INSTALL OVER CARPET OR ANY CUSHIONED BACKED PRODUCT. DO NOT INSTALL OVER ANY PRODUCT THAT IS NOT PROPERLY ADHERED.
1. Sub-floors MUST BE CLEAN, DRY, LEVEL, AND WELL BONDED.
2. Remove all existing trim throughout the room.
3. Measure the door clearance. If the door will not clear the floor, the door must be trimmed to fit from the bottom.
4. Install plastic sheeting on sub-floors. Always use moisture barrier plastic sheeting on any below grade floor and on all concrete floors. Overlap the plastic sheet 6-8 inches and tape the plastic sheeting with 2inch plastic or clear vinyl tape.
5. Use ¼” spacers to maintain the proper expansion gap around the entire perimeter of the floor. In large rooms, a ½” expansion gap may be preferred. IMPORTANT: this ¼” gap must be maintained around cabinets, pipes, toilet flanges and any other obstacles in floor.
6. Always work from left to right. Planks should run lengthwise against the longest wall, and if possible, parallel to incoming sunlight.
7. Always install tongue side facing wall.
8. A CASABELLA LAMINATE approved UNDERLAYMENT MUST be laid down prior to applying CASABELLA® LAMINATE.
Sub-Floors:
♦ Test floor for excessive moisture before installing over concrete, vinyl tile, concrete covered with ceramic tile, marble, stone, or linoleum. To do so, cut 3’ x 3’ squares of polyethylene plastic (one plastic square for every 200 sq. ft. of floor space). Spread plastic around different areas of the subfloor for a more accurate evaluation. Firmly tape down all edges of the plastic sealing them directly to the existing subfloor. Leave plastic down for 24 to 48 hours. Look for moisture under the plastic or for the cement to darken, this indicates excessive moisture.
♦ Always perform a Calcium Chloride Moisture Emissions Test. The maximum allowable reading is 3 lbs./1000 sq. ft/24 hours. You MUST retain your test and results to have a valid warranty.
♦ Concrete Sub-Floors – use minimum 6-mil polyethylene (plastic) sheeting as a vapor barrier. Roll out the plastic, overlapping the seam area 6 to 8 inches and tape the seamed with a 2” clear plastic sealing tape.
♦ Wood Sub-Floors – no additional plastic vapor barrier should be installed but subfloor must meet moisture restrictions. If moisture levels are too high, this must be alleviated before flooring is installed. Your contractor will need to diagnose your individual site conditions to solve this issue.
♦ WATER/PET RESISTANT FLOORS require that the entire perimeter of the installation must be sealed with 100% silicone sealant. All expansion spaces must be filled with 3/8” compressible PE foam backer rod and covered with 100% silicone sealant. You must apply 100% silicone sealant to all moldings at the point of contact with the flooring surface and at all connections to doorframes or any other fixed objects.
♦ Installations exceeding 4,356 sq. ft. must have the proper expansion joints installed.


BEGIN INSTALLATION:
♦ Begin the installation in the left-hand corner. Place the plank a minimum of ¼” from the left wall. Use spacers throughout all perimeter areas to ensure the correct expansion space is maintained. (a)
♦ Place the second plank tight against the short end of the first plank. (b)
♦ Fold down into the locked position with a single movement. (c)
♦ Place the final plank face down with the short side towards the wall. The remaining expansion space should be at least a minimum of ¼” from the wall. Draw a pencil line where the plank is to be cut. (d)
♦ Place the plank face down on the work surface and cut to size with a power saw. If you are using a hand saw, use a fine-toothed blade and cut the planks face up. (e)
♦ Begin the second row. The first and last planks in the rows should have a minimum length of 24 inches.
(g)
♦ The minimum distance between short ends of planks in parallel rows shall not be less than 24 inches.
(g)
♦ Connect the planks in the following rows by aligning the end seam of each plank directly above the end seam of the preceding plank. Insert the long side seam at a slight angle first and as the top surfaces meet, rotate the plank down into the locked position. (h)
♦ The distance to the walls can be adjusted when three rows are completed. (i) Remember to place the flooring a minimum of ¼” from all walls or other vertical obstructions such as cabinets, pipes, or columns. (j)
♦ In areas such as a doorjamb or cabinet kick base where planks cannot be angled to lock into place, use a wood chisel to remove the locking ridge from the bottom of the plank groove. Apply a 1/8” bead of tongue and groove adhesive to the bottom groove and gently tap the plank into place using a pull bar and hammer. Next, apply enough strips of painter’s tape across this seam to hold the joint securely in place until the adhesive sets. Using a clean, soft cloth, carefully clean up any excess adhesive on the surface of the planks. (k)
♦ On the first and/or last row where there is no polymer tongue on the short side, glue the joint with Clear Elmer’s glue where they join on the short end. (l)

DISASSEMBLY WHEN USING A LOCKING SYSTEM:

Your floor can be disassembled very easily, enabling replacement during installation and also during use. (m) Disassemble the panels by sliding them apart horizontally at the end seams. (DO NOT FOLD CONNECTED PLANKS UPWARDS!) (n)
RADIATOR PIPES:

♦ Drill the holes ¾” larger than the diameter of the pipes. (o)
♦ Remove all spacers.
♦ Install molding and transition pieces. Attach wood color coordinated molding or your desired trim and transition pieces using nails, screws or adhesive. NEVER ATTACH ANY MOLDING USING NAILS, SCREWS OR GLUE DIRECTLY TO DIAMONDLIVING FLOORING.


SPECIAL CIRCUMSTANCES
Doorways: Attempting to continue installing rows through a doorway into another room can be difficult because the narrow opening is a very small base upon which to continue consistent, straight and even rows into the next room.
T-moldings are available to install in doorways when joining flooring room to room.
To achieve alignment of plank rows from room to room, it is best to use a master reference line to run through the doorway to the far ends of each room involved. Position the line so that it is square and parallel from each room’s corresponding wall. Use this line to align the plank rows from room to room.
The maximum install in any direction is 66 feet before a transition is required.
Pipes, vents and other fixed objects: Each can be unique, but the general rule is to measure very carefully before you cut and remember to leave a 3/4″ expansion gap between the object and the flooring. You will cover expansion gaps with molding, vent covers or pipe rings when the floor is complete.
Installation on Stairs: Working from the top step down, flooring should be installed using adhesive and screw type fasteners or nails. All stair nose moldings must be glued and nailed, or screwed every 8”, for your safety. Glue down over cork: Using Casabella Laminate Approved flooring adhesive, CASABELLA® LAMINATE can be installed over a structurally sound concrete sub floor that is covered with full spread, permanently bonded acoustic cork. Cork thickness should not exceed 1/4” (6.35mm), with a density between 11.4 and 13 lb / cubic foot. Install cork in accordance with cork manufacturer’s recommendations. Acoustic cork should be pure cork with a polyurethane binder.

MOLDINGS, TRIM & TRANSITION PIECES
Installation Tips:
* Moldings should be acclimated 48 hours
* Moldings must be predrilled to avoid splitting whenever they are to be secured with nails or fasteners.
* The tool of choice for cutting hardwood moldings is a 10” or 12” motorized miter saw with pre-set adjustments for the basic miter cuts at 22.5°, 45°, and 90°. A carbide tipped blade makes the best finished cuts. Be sure the saw blade is positioned to cut into the finished face.
* When installing Wall Base molding, eliminate the need to putty as many holes on the molding by placing the bottom nail below the finished line of the Quarter Round.
* On Wall Base or Quarter Round moldings, never restrict the floor’s natural contraction/expansion movement by driving the fasteners at a downward angle. Attach the moldings to the wall or vertical surface.
* Always miter cuts rather than having butt cuts when splicing. Decide the direction of the miter by cutting the molding with the long point oriented in same direction as your natural line of vision when you enter the room. Wall Base - Borders the wood floor at the base of the wall to give the room a finished look. This molding along with the Quarter Round conceals the required expansion space between the wall and the flooring. It is also sometimes used under cabinets and toe kicks.
Quarter Round - This molding conceals the required expansion space between the wall/ wall base and the Laminate flooring. It is also sometimes used under cabinets and toe kicks where a wall base won’t fit or at the base of the stairs to provide a subtle blend between the floor and the wall or vertical surface.
Threshold –This molding is used at exterior doorways as a transition between flooring and the doorway threshold. It also can be used to transition a wood floor to different floor types to make them fit together perfectly, such as high pile carpeting or tile. Another typical use for a threshold is to conceal the expansion space between the flooring and a vertical surface such as fireplace hearths and sliding glass doors.
Installation: Lay the threshold molding in place to determine a proper fit. The threshold molding should overlap the flooring by 1/2” to 3/4” leaving the balance for expansion. To attach the threshold, nail into the subfloor behind the lip of the molding. Be sure when nailing not to obstruct the floors expansion space.
T Molding - Doorway molding used to join two wood floors in adjoining rooms. Also used when making


transitions from a wood floor to another floor that is approximately the same height, such as ceramic tile, hardwood, or laminate floors. T-Moldings are also used to provide expansion joints when a floor dimension exceeds the length or a width of 66’.
Installation: A space of 1 1/4” between the two adjoining floors is necessary to properly install the molding. This is to allow for the expansion space. Lay the T-Molding in place to determine proper fit. To attach the T- Molding between a ceramic tile floor and the floor, apply 1/4” bead of construction adhesive to the top edge of the ceramic tile. To attach between two floors, apply the 1/4” bead to the top edge of one side of the only. Seat the molding in place allowing for a minimum of a 1/4” overlap on the wood flooring. Make sure to allow for the expansion space between the T-Molding and the tile. When installing over a wood subfloor, use finish nails to secure T-mold. When installing over concrete, use heavy-duty construction adhesive to secure T-mold.
Overlap Reducer- (Floating Method) Used to join floors that utilize the floating installation method with floors of different heights such as vinyl, ceramic tile, or low pile carpeting.
Installation: To attach molding, pre-drill and nail in appropriate 6” to 8” intervals. Do not nail less than 2”- 3” from the ends of either side. To attach the molding using glue, apply glue to the front edge of the molding.
Apply one or two 1/4” beads of construction adhesive to the subfloor and seat the molding in place. It is important not to attach the reducer directly to the floating floor to allow expansion and contraction.
Overlap Stair Nose – (Floating Method) provides the proper transition for stairways or steps, which have floors that have been installed using the floating installation method. The
Stair Nose also provides the proper overhang for a transition from one floor level to the next such as the step into a sunken living room.
Installation: To attach molding, pre-drill and nail in appropriate 6” to 8” intervals. Do not nail less than 2”- 3” from the ends of either side. Also apply glue to the front edge of the molding. Apply one or two 1/4” beads of construction adhesive to the subfloor and seat the molding in place. All stair nose moldings must be nailed and glued to secure the molding adequately. It is important not to attach the reducer directly to the floating floor to allow expansion and contraction.
Flush Reducer - Used to join floors that have been glued down or nailed down to transition with floors of different heights such as vinyl, ceramic tile, or low pile carpeting.
Installation: To attached molding pre-drill and nail in appropriate 6” to 8” intervals. Do not nail less than 2”- 3” from the ends of either side. To attach the molding using glue, apply glue to the front edge of the molding.
Apply one or two 1/4” beads of construction adhesive to the subfloor and seat the molding in place.
Flush Stair Nose - Provides the proper transition for stairways or steps which have floors that have been installed by either the nail down or glue down installation method. The Stair Nose also provides the proper overhang for a transition from one floor level to the next such as the step into a sunken living room.
Installation: When used on a stair step, the Stair Nose molding should cover and overlap the riser. When used on a step-up to another room, the Stair Nose molding becomes the starting “edge” of the floor. Because of the interlocking of the molding with the floor, the Stair Nose molding should be installed first. Once the molding is in place, the interlocking floor can be installed. Moldings should be installed using adhesive and screw type fasteners or nails.

We guarantee to the original purchaser that Casabella© Laminate ScubaTech™, when installed by a certified installer who follows all, without exception, of the installation instructions, and is placed in a dry climate controlled indoor setting:
• Will not fade in color due to sun or artificial light.
• Will not stain from normal household consumable items such as food and drink.
• Will resist water damage from normal household activities when installed in accordance with provided installation instructions and not installed in an area with excessive moisture. Before installation, a moisture test, to determine if excessive moisture exists in the sub floor (using ASTM 1869 calcium chloride test) any levels above 3 lbs/1000 sqft or over 70% using an in-situ probe (as per ASTM F2170) are excessive, MUST be performed on all subfloors. A 6mil polyethylene film vapor barrier MUST be used on concrete subfloor along with proper use of silicone sealant. A polyethylene film vapor barrier is not required over wood subfloors, but moisture readings must be < 8% throughout the entire installation. TO HAVE A VALID CLAIM, VERIFIABLE PREINSTALLATION MOISTURE TEST DATA MUST
BE RETAINED AND PRESENTED AT THE TIME OF THE CLAIM. This warranty does not cover moisture/liquid damage caused by, to include but not limited to, flooding, standing water (water remaining on a floor for more than one hour except for Casabella© Laminate ScubaTech™ labeled as Water Resistant in their name/label as described below in this paragraph), appliance leaks, pet waste, mechanical failures, leaking pipes, or damage caused by moisture/liquid underneath the flooring, including but not limited to, damage from sub floor hydrostatic pressure.
• Casabella© Laminate ScubaTech™ sold after November 2017 are warrantied for 5 years to protect against surface spills of water and pet urine only for spills/pet urine lasting 72 hours or less on the floor. All spills/ urine need to be dried within 72 hours or the warranty will be voided. Spills or pet urine that is allowed to remain longer than 72 hours inside a beveled edge and causes delamination or bubbles/blisters will void this warranty. Be sure to dry the bevel edges on all spills or pet urine to protect your warranty.
• This warranty does not cover water damage caused by flooding, standing water (water remaining on a floor for more than 72 hours), appliance leaks, pet waste, mechanical failures, leaking pipes, or damage caused by water underneath the flooring including damage from sub floor hydrostatic pressure. This product is subject to all the moisture testing and other requirements as listed above and below to have a valid surface spill warranty. The entire perimeter of the installation must be sealed with 100% silicone sealant. All expansion spaces must be filled with 3/8” compressible PE foam backer rod and covered with 100% silicone sealant. You must apply 100% silicone sealant to all moldings at the point of contact with the flooring surface and at all connections to doorframes or any other fixed objects.
• The wear layer will not wear through. For surface wear to be a warrantable occurrence, the surface wear- through must be readily visible in normal light and from all directions and from a distance of 6 feet and measure at least 1 square inch. Gloss fading is not wear-through.

Underlayment:
To have a valid Warranty, you must install underlayment under your Casabella© Laminate ScubaTech™ flooring where appropriate.

This limited warranty does not cover any damages due to:
• Any damage caused by subfloor moisture or any surface moisture other than water/pet urine is not a warranty claim and will be denied for any form of compensation. This includes, but is not limited to, BUBBLES IN PLANKS, DELAMINATION ON ENDS OF PLANKS, SWELLING OF PLANKS, ETC. EXCESSIVE MOISTURE WILL CAUSE THE FINISH AND STAIN TO SEPARATE FROM THE


PLANKS. THIS IS NOT COVERED BY CASABELLA© LAMINATE SCUBATECH™ OR ANY OTHER MAJOR MANUFACTURER WARRANTY. THIS TYPE OF CLAIM SHOULD BE FILED WITH YOUR HOMEOWNER INSURANCE CARRIER.
• Abusive conditions including, but not limited to, damage from roller casters if protective floor mat is not used, heavy items placed on flooring without floor protectors, etc.;
• Moldings of any type;
• Damages due to mats, improper Maintenance, failure to follow proper Installation or Care instructions such as but not limited to Damage from Vacuum cleaner beater bar or hard heads, Reduction in gloss level due to pebbles, sand or other abrasives, etc. are not covered; USING UNAPPROVED CLEANERS SUCH AS MURPHY OIL, FLOOR POLISH, SHARK STEAMER, ETC. – THESE PRODUCTS WILL LEAVE A RESIDUE ON YOUR FLOOR THAT MAY NOT COME OFF AND/OR MAY CAUSE YOUR FLOOR TO MAR OR DELAMINATE.
• Damages (marks, scuffs, scratches, dents, cuts, etc.) caused by, but not limited to, Insects, Acts of God, Fire, Flooding, Negligence, Improper fabrication, Improper installation, improper maintenance, Accidents, Misuse, Abuse, Appliances, Casters, Furniture, Pets, Burns, Construction, and planks being engaged or disengaged more than three times are not covered;
• Installation of flooring that contains any visible or known/should have known manufacturing defects;
• Failure caused by structural changes in the sub floor, uneven subfloor or damage to the subfloor due to settling of the structure;
• Unauthorized repair or replacement without express prior written approval from CASABELLA© LAMINATE SCUBATECH™ warranty center;
• This warranty is issued to the original purchaser and is not transferable. The original purchaser must, within 30 days of this purchase, register their purchase by mailing the CASABELLA© LAMINATE SCUBATECH™ Warranty Card (provided below) along with proof of purchase to the CASABELLA© LAMINATE SCUBATECH™ warranty center. CASABELLA© LAMINATE
SCUBATECH™ is not responsible for undelivered or lost warranty information;
• IT IS THE CONSUMER’S, INSTALLER’S, AND RETAILER’S DUTY TO INSPECT THE PLANKS BEFORE THEY ARE INSTALLED. CASABELLA© LAMINATE SCUBATECH™ WILL EXCHANGE, AT NO COST TO THE CONSUMER, ANY PLANK THAT THE CONSUMER, INSTALLER, OR RETAILER REASONABLY OBJECTS TO BEFORE INSTALLATION. THE CONSUMER, INSTALLER, AND RETAILER AGREE THAT BY INSTALLING A PLANK, THEY HAVE ACCEPTED THE COLOR, GLOSS AND ALL OTHER VISIBLE ASPECTS OF THE PLANK. ANY WARRANTY CLAIM, EXCEPT FOR STRUCTURE, FINISH, OR WEAR WILL BE DENIED;

• Many laminate flooring products use the same décor design therefore, TO FILE A WARRANTY CLAIM, YOU MUST RETAIN YOUR ORIGINAL INVOICE AND PROOF OF PURCHASE INFORMATION THAT PROVE:
o YOU ARE THE ORIGINAL PURCHASER,
o IT IS A CASABELLA© LAMINATE SCUBATECH™ PRODUCT, and
o YOUR RETAILER’S INFORMATION, INCLUDING BUT NOT LIMITED TO, ALL COST AND SQUARE FOOTAGES;



What will Casabella© Laminate ScubaTech™ do if it is determined that there is a valid warranty claim:
• FOR THE MATERIAL: If any of the covered events listed above occurs within the warranty period, Casabella© Laminate ScubaTech™ will, at its own discretion, replace or repair the failed portion of the product with the same product unless that product is no longer available. Under this warranty, only failed planks will be replaced, not the surrounding planks that are still performing. If the original product is no longer available, Casabella© Laminate ScubaTech™ will, at its own discretion, replace the damaged product with a comparable product or refund the portion of the original purchase price of the failed flooring only.
• FOR THE LABOR: For the first two years after installation, Casabella© Laminate ScubaTech™ will pay
$2 per sq ft to replace the failed flooring from the nearest wall. After two years but less than five years Casabella© Laminate ScubaTech™ will pay $1 per sq ft to replace the failed flooring from the nearest wall. After five years, no labor cost will be paid.
• If CASABELLA© LAMINATE SCUBATECH™ chooses to replace Flooring that fails to meet the warranty, it will only be replaced one time.
• THIS LIMITED WARRANTY DOES NOT INCLUDE REMOVAL OR REPLACEMENT OF CABINETS, FIXTURES, RETAIL MARKUPS, INSTALLATION OR LABOR PROVIDED BY OTHERS OR SUPPLEMENTAL COST, INCLUDING BUT NOT LIMITED TO RELOCATION DURING THE REPAIR PROCESS SUCH AS HOTELS, MEALS, OR MOVING AND STORAGE OF FURNITURE.

THIS WARRANTY DOES NOT COVER ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL OR EXEMPLARY DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY AND DISCLAIMS ALL OTHER EXPRESS OR IMPLIED WARRANTIES. NO IMPLIED WARRANTIES EXTEND BEYOND THE TERMS OF THIS WRITTEN WARRANTY. SOME STATES DO NOT ALLOW THE LIMITATION OF CONSEQUENTIAL DAMAGES, SO THIS MAY NOT APPLY TO YOU. THE ABOVE REMEDIES ARE THE CUSTOMER’S SOLE AND EXCLUSIVE REMEDIES FOR CLAIMS ON THIS PRODUCT.

WITHIN 30 DAYS OF PURCHASE YOU MUST PHOTOCOPY AND COMPLETE THE ‘WARRANTY REGISTATION CARD’ (NEXT PAGE) AND MAIL BACK TO CASABELLA© LAMINATE SCUBATECH™ TO HAVE A VALID WARRANTY!

Casabella® LAMINATE FLOOR CARE AND MAINTENANCE

♦ PLEASE REMEMBER, like any floor covering, our factory finished floors will show signs of wear over time, depending on the size and lifestyle of your family. By observing a few precautions along with setting up a regular cleaning and maintenance program, you can expect years of beauty from your floor.
♦ REGULAR CARE AND MAINTENANCE: Regular cleaning and sweeping of sand and dirt is required to maintain your new Casabella Laminate flooring surface. Sweep or vacuum regularly since built- up grit will damage the surface of the wood. The vacuum head must be a brush or felt type. Be certain the wheels of the vacuum are clean and do not damage the finish. Do not use a vacuum with a beater bar head.
♦ SPILLS: Remove all spills immediately. Use a dry or damp cloth to wipe the surface clean and dry. CAUTION: FLOOR SURFACE IS VERY SLIPPERY WHEN WET. ALLOW FLOOR TO DRY BEFORE WALKING ON SURFACE.
♦ CLEANING: Use CASABELLA® LAMINATE approved products to maintain your floor. Bona Laminate Cleaner can be used. Consult an approved dealer for instructions. ALWAYS SWEEP OR VACUUM THE FLOORS PRIOR TO USING WOOD FLOOR CLEANERS. DO NOT ALLOW EXCESS CLEANER TO REMAIN ON THE FLOORS SURFACE AS THIS MAY PERMANENTLY DAMAGE THE WOOD.
♦ DO NOT USE HARSH CLEANERS OR ABRASIVE CLEANING PRODUCTS TO CLEAN CASABELLA® FLOORING. NEVER WET-MOP, DAMP-MOP, OR CLEAN YOUR FLOOR WITH WATER OR OTHER PRODUCTS. THIS CAN SEVERELY DAMAGE THE FLOORING AND WILL VOID THE WARRANTIES. DO NOT USE FLOOR CLEANING MACHINES OR STEAM CLEANERS.
♦ DO NOT USE 2 IN 1 CLEANERS – THE USE OF THESE PRODUCTS WILL VOID THE FINISH WARRANTY AND MAY PRODUCE UNSATISFACTORY RESULTS WHEN NOT APPLIED PROPERLY. DO NOT USE OIL, SOAPS, LIQUID OR PASTE WAX PRODUCTS OR OTHER HOUSEHOLD CLEANERS THAT CONTAIN CITRUS OILS, LEMON OIL, TUNG OIL, SILICON, OR AMMONIA SINCE OUR WARRANTIES DO NOT COVER DAMAGE CAUSED BY NON-RECOMMENDED PRODUCTS. USE OF THESE AND OTHER SUCH PRODUCTS WILL HARM THE LONG-TERM PERFORMANCE OF YOUR FLOOR AND WILL VOID YOUR WARRANTY.
♦ FURNITURE:
1. NEVER SLIDE FURNITURE OR OTHER HEAVY ITEMS ACROSS FLOOR.
Always protect the floor surface when moving items across the floor. Use a dolly and protective sheets of plywood when moving heavy objects, furniture, or appliances.
2. NEVER PLACE HEAVY OBJECTS ON THE FLOOR WITHOUT “FLOOR PROTECTORS”.
3. NEVER PLACE HEAVY FURNITURE ON FLOOR FOR EXTENDED PERIODS OF TIME WITHOUT FLOOR PROTECTORS. AVOID HARD ROLLING CASTERS. USE FLOOR PROTECTOR PADS FOR
ROLLING CHAIRS. Make certain furniture casters are clean and operate properly (a minimum 1” wide vinyl surface where it comes in contact with laminate is recommended). Clean wheels periodically to remove dirt and debris.
♦ HOT ITEMS: NEVER place “HOT ITEMS” on the floor surface.
♦ PETS: Clean up pet waste immediately as it is harmful to your CASABELLA® LAMINATE. Keep pets’ nails trimmed, and paws clean and free of dirt, gravel, grease, oil, and stains.
♦ REMOVE SHOES with spiked or damaged heels before walking on floor.
♦ MAINTAIN THE PROPER RELATIVE HUMIDITY in your home between 35% - 55%. The use of a humidifier during heating seasons may help reduce shrinkage of the wood due to low humidity.

MAINTENANCE TIPS:
♦ Place outside doormats in all outside doorways to reduce dirt and moisture.
♦ Wipe up all moisture spills immediately.
♦ Clean the floor often.
♦ Do not use excessive water.
♦ Do not use unapproved cleaners, soaps, or detergents. MANY OF THESE PRODUCTS WILL DESTROY THE FINISH ON YOUR FLOOR. BE VERY CAREFUL NOT TO USE CLOTHS CONTAMINATED WITH OTHER CLEANING PRODUCTS ON YOUR FLOORS. IT WILL VOID YOUR WARRANTY.
♦ BONA HARDWOOD FLOOR CLEANER AND TERRY CLOTH MOP KIT WILL REMOVE MOST SUBSTANCES FROM YOUR FLOOR.
USE CASABELLA LAMINATE™ FLOORING APPROVED PRODUCTS FOR LONG LASTING PERFORMANCE AND BEAUTY. FAILURE TO FOLLOW THE ABOVE CARE AND MAINTENANCE TIPS WILL VOID YOUR WARRANTY.