Warm Latte Casabella Lincoln Highway Laminate

Dimensions: 12mm x 8" x 47.6" - 12 mil Wear Layer
Construction: Plank
Design: Laminate
Coverage: 15.94/SQ.FT
Edge Style: Nano Bevel
Finish: NanoTek
Install Method: Tight Lock
Certification: FloorScore
Warranty: 30 Year Residential - 5 Year Commercial

Overlap Stair Nose
Overlap Reducer
Quarter Round
Square Nose
Scuba Thermo Silent Underlayment

Installation Instructions for Casabella Laminate

A. Products should be staggered in brick laid pattern; stagger equal to half of a plank for the first 2 rows, and then at least 18” for the following rows. Spacers should be placed against walls to maintain proper distance (1/4” - 1/2”). Tools needed: planks, underlayment, spacers.

B. The first row must be installed
straight. Begin installation back and forth between rows one and two for the first two rows only. Start small plank positioned close to the wall, angle a long plank into the long side of the short plank, and drop long plank tongue into lock. Make sure there are
no gaps.

C. Take another long plank, repeat the
previous step, insert the long side of plank into long side of previous plank. Then slide plank to your left until the short side is in contact with the short side of the first laid plank.

D. Using the drop lock system, drop the short side of the last long plank into the short side of the first laid plank. Slightly tap on the top of the joint of the short side with your fist to secure.

E and F. Finishing rows 1 and 2– continue alternating planks on rows 1 and 2 to avoid misalignment. From row 3 onwards, installation does not require alternating rows. Install one row after the other by starting with angling on the long side, sliding until the short sides are in contact and then locking the short side. As you go, ensure the short sides are securely locked by tapping with your fist, or if need be, a rubber mallet.

G. Remove spacers and cover gaps with a trim.

General Requirements:
It is the sole responsibility of the installer/owner, prior to installation, to assure that the planned installation area is suitable for the flooring and meets local building codes. Confirm that all subflooring meets or exceeds all industry standards and local building codes; as well as the recommendations listed herein. The manufacturer accepts no responsibility for product failure extending from or related to failure to meet job environment and subflooring requirements. The installer/owner assumes full responsibility for the final inspection of this product. Inspection should be done prior to installation and should include: print/color/texture/ factory finish /visible conditions. If the product is not acceptable, DO NOT INSTALL IT. Contact your supplier immediately for assistance. Flooring that has been installed will be deemed to have been inspected and quality accepted. Casabella will not accept any responsibility for any flooring installed with visible defects. This product is waterproof but is not a moisture barrier. Water traveling over or around the outer edges of the flooring wont damage the structure of the flooring but can damage the subfloor. This damage to the subfloor is a site related condition and/or associated conditions are not warranted. In addition, other contaminates could migrate up in the moisture, as well. These are not manufacturing related conditions and are not covered by your warranty. Elevated moisture levels below your flooring can migrate through the joints as vapor emissions possibly causing a milky white appearance known as Blushing. Blushing is a site related condition, and thus is not covered by your warranty. It may dissipate once the moisture levels have
decreased. When installing in a lavatory, bathroom, laundry room, or other area with frequent water usage, it is possible for water to travel under the floating floor and create bacterial growth and the problems associated with it. These are not manufacturing issues, not covered by your warranty, and should be mitigated before installing the flooring and should be dried, as necessary.
Always allow ½" expansion space around the entire perimeter of the room and at all fixed objects/fixtures and pipes for any installation under 4,356 sq. ft. and runs less than 66 feet. For jobs above 4,356 sq. ft. and runs greater than 66 feet, use transition pieces and allow at least 5/8 inch for expansion. Cabinets may be installed over your flooring, but appropriate expansion areas must be maintained around any fixed objects including pipes. Cabinets should be fastened to the walls and not to the flooring. Do not allow screws or nails to penetrate flooring.
Preparing the Area
Remove all furniture and appliances from the room(s). Remove wall and doorway trim. Undercut door casings and remove all debris and equipment that may damage finish. Do not install over soft, rough, uneven surfaces, or
floating floors. The Flooring should only be installed after all the other trades have finished and the jobsite has been cleared of any/all debris that could damage a finished installation. All sub-floors and substrates must be clean, flat (smooth) and dry prior to installation. Sweep or vacuum your subfloor prior to installation ensuring
nothing will interfere with the installation. All subfloors must be flat. High or low areas exceeding 3/16” per 10’ (7.5 cm in 3 meter) or 1/8” per 6’ (2.5 cm in 1.8 meter) must be corrected. Permanent HVAC should be on and operational a minimum of 5 days and maintained between 65° – 75° (F) and a relative humidity of 35%- 55% prior to delivery, during, and after installation of the flooring.
Wood Subfloors
This product is suitable for installation over a minimum of 3/4” CDX Plywood, OSB, or APA approved plywood. All wood subfloors should be flat, structurally sound, and free from deflection (up and down movement). Sand high
areas and fill low areas with a Portland based patching compound. To avoid squeaking of the subfloor, nail or screw the floor every 6”. Repair or replace any damaged sheathing. Joist spacing should not exceed 19.2". Set fasteners
1/32" below the subfloor surface, sand joints, smooth and fill holes, or gaps wider than 1/8 inch wide. Install
suitable underlayment when necessary to achieve a flat or solid surface. Next generation planks can be installed

over underlayment grade plywood, lauan plywood and other underlayment recommended by the manufacturer for use with rigid core flooring. Installation over oriented strand board and particle board is not recommended unless
it is underlayment grade and non-weathered since these panels present a greater risk of sub-floor instability and can detract from the performance of the floor. Wooden subfloors installed over a crawl space should have a moisture barrier installed in the crawlspace with at least 18 inches of ground clearance with a black ground cover minimum 6mm thick Polyethylene overlapped a minimum of 6” (115 cm) and taped using a moisture resistant tape to avoid moisture migration from the ground up through the flooring. Cross ventilation (vents located around the perimeter) equal to 1.5% of the square footage of the area should be highly considered (if not already a local code). Wood floors installed directly on concrete or installed over sleeper construction are not satisfactory for installation and should be removed. Repair all squeaks prior to installation. Wood subflooring moisture should not exceed 15%. Install planks at a 90° angle to any existing wood floor. NOTE: Avoid subfloors with excessive vertical movement or deflection because subfloor movement will telegraph through to the finished installation. Indications of excessive deflection are subfloor fastener release, squeaking, compromised, or sectional contours such as bowing or dipping in floors and uneven flooring material. Nail or screw subfloor panels to secure boards with excessive vertical movement (deflection) before installation. If the subfloor has excessive vertical movement (deflection) before installation of the flooring, then it is likely it will do so after installation of the flooring is complete. Our warranties DO NOT cover any problems caused by inadequate substructures or improper installation of said structures. The
suitability of any subfloor is the responsibility of the installer and the final consumer.
Concrete Subfloors
The flatness of concrete subfloors must meet or exceed the requirements of ACI FF25. Most concrete subfloors are not flat/smooth and must be properly prepared before installation. In all cases, verify the substrate is flat (See above subfloor and substrate requirements). All concrete floors must be properly cured and allowed to dry for at
least 60 days after the curing process. This product can be installed over concrete on all grade levels.
Ceramic tile and terrazzo:
All wax and sealers must be removed with an appropriate cleaner/stripper. Ceramic tile and terrazzo should be abraded to allow for proper adhesion. Check for loose tiles by tapping and re-adhere. Fill grout lines with a
cementitious latex fortified leveling compound. Resilient tile, resilient sheet vinyl: Material must be full spread and secured to the subfloor. Do not install over perimeter glued floors. Do not install over more than one layer that
exceeds 1/8” in thickness.
Acoustic Cork Underlayment:
(Glue Down Only) – Install the cork underlayment according to the manufacturer’s instructions. The cork underlayment must be fully adhered to the subfloor. The cork underlayment should be of pure granulated cork combined with a polyurethane binder with a minimum density of 11.4 lbs. per cubic foot and not to exceed 13 lbs. per cubic foot.


Radiant Heat Guidelines:
• Newly installed water-type radiant heating flooring systems should be in operation, with the temperature set between 64°-72 °F, for a minimum of 4 weeks. This will ensure that any subfloor moisture has properly dried. • Older/existing water-type radiant floor heating systems need to be fully pressure tested, properly maintained, and set to a minimum of 64° F for at least 4 days before delivery, acclimation or installation of the flooring begins. •

Electric mat or mesh radiant heating systems many times are not acceptable. They must be specifically designated as suitable for use with laminate flooring systems by the manufacturer. Casabella makes no warranties as to their suitability and disclaims any defects caused by them. • Always check wood sub-floors to ensure that the moisture content is less than 10% using an accurate wood moisture meter. Concrete sub-floors must register "dry" using a reliable concrete moisture meter. • The PH level of concrete sub-floors should register between 6 and 9.• Sub- floors must fully comply with Casabella "dry" requirements before proceeding with the delivery, acclimation, installation and any other required curing processes. • Regulate the job site to ensure that the relative humidity is between 35 and 65 percent, and that the temperature is between 60° and 80° F, throughout the flooring delivery, acclimation, and installation. • After completing the installation, do not change/adjust the radiant heat settings for at least 48 hours. At any given time after the initial 48-hour period, the homeowner should only increase or
decrease the temperature settings 4° to 5° F per day, so that the laminate flooring can gradually adjust to the temperature changes. • Never raise the flooring surface temperature setting above 85° F. • It is important to note that when wood products are used over a radiant heating system, minor gapping can occur and should be
expected. Maintaining consistent relative humidity levels will help to minimize this occurrence. Seasonal changes can also have the same effect on laminate, so temperature and humidity controls should always be monitored to ensure the best performance.
Mold/Mildew
Mold/Mildew are not covered by your warranty and may destroy the functionality/aesthetics of your purchase. Mold/Mildew is a function of excessive moisture in the foundation of your home or from a water source in your home.
Moisture
It is recommended that your slab have less than 5% Moisture content, 5 lbs./1000 sq ft/24 hours MVER and less than 75% RH. Exceeding these numbers will not directly damage this product but can lead to many hazardous and damaging conditions (mold, mildew, rot) that are not covered by your warranty.
MAINTENANCE TIPS:
Place outside doormats in all outside doorways to reduce dirt and moisture. Wipe up all moisture spills
immediately. Clean the floor often. Do not use excessive water. Do not use unapproved cleaners, soaps, or detergents. MANY OF THESE PRODUCTS WILL DESTROY THE FINISH ON YOUR FLOOR. BE VERY CAREFUL NOT TO USE CLOTHS CONTAMINATED WITH OTHER CLEANING PRODUCTS ON YOUR FLOORS. IT WILL VOID YOUR
WARRANTY. BONA HARDWOOD FLOOR CLEANER AND TERRY CLOTH MOP KIT WILL REMOVE MOST SUBSTANCES FROM YOUR FLOOR.
RETAILER/INSTALLER/OWNER RESPONSIBILITY
Carefully inspect all Casabella flooring prior to installation for defects/objections: TO REPLICATE NATURAL WOOD, CASABELLA CREATES A SLIGHT BACKGROUND COLOR VARIATION ON EACH PRODUCTION RUN. JUST LIKE REAL WOOD, THIS LAMINATE WILL HAVE A NATURAL COLOR VARIATION. THEREFORE, BE SURE YOU ARE SATISFIED WITH THE BOXES YOU HAVE PURCHASED. IF YOU ARE IN ANY WAY DISSATISFIED, CASABELLA WILL
UNCONDITIONALLY ACCEPT UNINSTALLED RETURNED PRODUCT. ONCE YOU INSTALL, THIS OFFER IS NO LONGER
VALID. Materials installed with visible defects are not covered under our warranty. This is an industry standard.
Accepting or rejecting the material must be done on full cartons, not plank by plank. Casabella flooring has one of the lowest warranty rates in the industry and the highest manufacturing standard in the industry. We want you to be satisfied with your purchase.

You MUST, as the final inspector, inspect for proper color, finish, style, and quality PRIOR to installation. Verify that the flooring is the correct material. Care should be taken at this time to remove or repair particular characteristics you do not desire. IT IS YOUR RESPONSIBILITY TO INSPECT THE FLOORING BEFORE IT IS INSTALLED. IF YOU ARE NOT SATISFIED WITH THE FLOORING PRIOR TO INSTALLATION, CONTACT YOUR DEALER. DO NOT INSTALL THE FLOORING. IF YOU INSTALL THE FLOORING, YOU HAVE ACCEPTED ITS MANUFACTURED APPEARANCE.
MANUFACTURER SHALL NOT BE RESPONSIBLE FOR ANY COSTS INCURRED WHEN PLANK(S) WITH VISIBLE DEFECTS HAVE BEEN INSTALLED. A VISIBLE DEFECT IS ANY DEFECT THAT EXISTS BEFORE INSTALLATION AND WAS VISIBLE TO THE NAKED EYE. IF YOUR LAMINATE FLOORING IS INSTALLED PROPERLY AND NOT DAMAGED BY EXCLUSIONS NOT COVERED BY OUR WARRANTY, CASABELLA WILL ALWAYS WARRANTY THE STRUCTURE OF YOUR
FLOORING AS PER THE WARRANTY AGREEMENT. The use of stain, filler, or putty stick for the correction of minor defects during installation should be accepted as normal procedure. An 8% cutting allowance, depending on layout, must be added to the actual square footage amount needed. (Some installations will require a higher percentage.)

WARRANTY

STOP! READ!

ATTENTION! READ BEFORE INSTALLING!
ALL FLOOR COVERINGS SHOULD BE PROFESSIONALLY INSTALLED TO ENSURE A VALID WARRANTY.
We warrant all our products to be free from defects in material and workmanship, under normal use and service, for a specified length of time from the date of purchase as set forth below. This Limited Warranty only applies provided the flooring covered by this warranty is installed and maintained according to our Installation & Maintenance Manual. Please refer to the installation manual for the proper moisture content of the subfloor, all year round relative humidity/temperature and all proper guidelines to ensure that the warranty remains valid.


LIMITED RESIDENTIAL USE WARRANTY SCOPE OF APPLICATION
This Limited Residential use warranty is offered by us and is Worldwide applicable. This warranty applies to our waterproof surface
laminate flooring, purchased from authorized dealer and installed and used residentially. Residential use is defined as normal household use.

WARRANTIES
WEAR WARRANTY
We warrant to the original purchaser that the wear layer on our flooring:

• Will not wear through the decorative surface. Scratches, indentation or reduction in gloss level is not considered wear.
• Will not fade as a result of direct sunlight or normal indoor lighting.
• Will not stain from normal household use.
• In its original manufactured condition, will be free from manufacturing defects.
• Starting from the date of purchase, but only if no exclusions are applicable and only if all conditions are fulfilled.

STRUCTURAL WARRANTY
• We warrant the original purchaser that our flooring:
• Will not delaminate.
• In its original manufactured condition, will be free from manufacturing defects.
• Starting from the date of purchase, but only if no exclusions are applicable and only if all conditions are fulfilled.

INSTALLATION OVER A RADIANT-HEATED SUBFLOOR WARRANTY
We warrant to the original purchaser starting from the date of purchase, the floor can be installed over a radiant-heated subfloor, but only if no exclusions are applicable and only if all conditions are fulfilled. This radiant-heated subfloor warranty is only applicable when at least the following cumulative requirements are fulfilled. The radiant heating system has to be a water pipe radiant heating system (this means for example that we do not warrant installation over electrical radiant heating systems). The radiant heating system must incorporate electronic temperature controls. Before installing over newly constructed radiant heat systems, operate the system for 3 weeks at maximum capacity to force any residual moisture from the cementitious topping of the radiant heat system. Then set the thermostat to a comfortable room temperature for the installation. It is recommended that the radiant heat be applied in a gradual manner after installing the flooring. Refer to the radiant heat system's manufacturer recommendations for additional guidance. faximum operating temperature should never exceed 810F / 270C.
PET WARRANTY
We warrant that the floor will resist staining caused by pet (domestic cat or dog) stains, including urine, feces, and vomit. Stain resistance means the ability of your floor to resist (i.e., minimize or withstand) permanent stains for the warranty period. However, accidents should be cleaned up immediately, as the longer they sit, the more difficult they will be to remove. Any damage to the subfloor and/or surrounding structure caused by pets is not covered by this warranty.

RESIDENTIAL WATERPROOF SURFACE FLOORING WARRANTY
When properly installed, the floor will not be damaged by topical, localized spills resulting from normal household use, such as wet shoes, liquid spills, dripping while exiting a bath tub or shower. Flooding is NOT covered by the warranty, which means standing water must be avoided at all times.
LIGHT COMMERCIAL WATERPROOF SURFACE FLOORING WARRANTY
Light commercial use means: use in environments (which do not have heavy commercial traffic) such as outlined in the application table
below.

Examples of business type commercial use Recommended application

Professional oices, Medical oices.
All non-required “clean room” areas – Corridors, patient rooms, lobby, waiting rooms, cafeteria, exam rooms, common areas.
Offices, banks. Offices, hallways, lobby, reception areas, break rooms,
conference rooms.

Boutiques, retail store, art galleries, book-stores, coffee shops, gift shops, jewelery stores, beauty salons, barber shops.
Dressing rooms, entire store.

EXCLUSIONS AND CONDITIONS
• Damage arising by not following relevant installation, care, maintenance and use instructions of the present warranty and the installation instructions provided.
• Damage arising from improper installation (for example installation on an unleveled subfloor and installation when there is not sufficient perimeter expansion zone), improper care, improper maintenance or improper use.
• Damage arising because the flooring is exposed to extreme cold (below 600F) or extreme heat (above 850F .
• Damage arising because the flooring is exposed to low or high humidity not within 30o - 60o:
• Damage caused by exposure to moisture (for example moisture in a concrete slab, moisture from hydrostatic pressure, flooding, standing water, water underneath the flooring, moisture as the result of malfunctioning appliances such as dishwashers, ice makers, refrigerators, sinks, pipes).
• Normal wear and tear of the flooring.
• Normal changes in color, gloss, grain pattern and tone (this is normal for flooring as it ages).
• Damage arising because the flooring is installed in an outdoor area, a solarium, a porch, a garage or areas similar to all of these.
• Damage arising from excessive steam mopping.
• Damage arising from accidents, abuse, misuse, or the use of strong chemicals.
• Damage caused by an act of God (for example a natural disaster).
• Damage caused by vacuum cleaner beater bars or hard plastics, or metal caster wheels.
• Damage caused by wheelchairs.
• Differences in aspect, color, gloss, grain pattern and tone with the reference flooring sample in for example the store or showroom.
• Flooring that has been damaged or neglected during transportation.
• Scratches, marks, stains, indentations and other damage caused by exposure to 'abrasives' such as pebbles, grit, sand, high heeled shoes, furniture, etc.
• Damage to click joints or indentation due to heavy rolling loads.
• Damage of planks coming apart at the seams because they have been engaged/disengaged more than three times.
• Damage caused by the collections of dirt and moisture at entrances do due the lack of interior and exterior doormats.
• Damage caused by shoes having heel taps or sharp objects protruding from the sole such as rocks, exposed nails and gravel.
• Damage caused by walking on with spike-or stiletto-heeled shoes.
• Damage caused by sliding or rolling heavy objects on the floor. A solid protective covering must be laid (must use at least 1/4' / 6.35 mm hard board) on your floor and gently 'walk' the item a cross it. Carpet or cardboard is not adequate to prevent surface indentation or roller marks from occurring or scratches to the floor.
• Damage caused by non-compliant casters on furniture. Barrel-type caster wheels or wide, flat glides are best for protecting the floor. For areas with rolling chairs (e.g. desk area), ensure a protective mat is used under the chair.
• Damage caused by hard narrow furniture rollers. They must be replaced with wide rubber rollers.

This warranty is valid only to the original purchaser. It is not transferable and only applicable to the first installation of the flooring. The affected area must be visible and cover an area bigger than 0.04 in / 25 mm2. This warranty does not apply to any products designated as B grade, cabin grades, closeouts, seconds, factory special, non-standard items and flooring sold 'as is'.

It is the responsibility of the purchaser and the installer, whether they are professionals or a do-it-yourselves, to inspect all flooring and flooring accessories before installation. If during inspection the purchaser or the installer knows/discovers or can reasonably be supposed to know/discover (for example when the default is visible), that the flooring has a visible manufacturing issue, do not install the flooring. Please immediately contact the retailer from which the flooring was purchased. No claims will be accepted for flooring of which the purchaser or installer knew/discovered or can reasonably be supposed to have known/discovered, that there was something wrong with it. In such case we only warrant the part of the flooring which has not been installed yet.
We do not allow or authorize any other person or entity to alter the obligations and limitations in this warranty. This warranty is the complete and exclusive expression of our warranty and is in lieu of all other express and/or statutory warranties. Any implied warranties, including but not limited to the implied warranties, merchantability and fitness for a particular purpose are limited to this express warranty. However, some jurisdictions do not allow exclusion or limitation on how an implied warranty lasts, so the above limitation or exclusion may not apply to you.

We expressly exclude and will not pay consequential or incidental damages under this warranty. By this we mean for example loss, expense, inconvenience or damages, other than to the flooring itself, that may result from a defect in the flooring. However, some jurisdictions do not allow exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

We reserve the right to inspect the flooring and to remove samples for additional evaluation, if we consider this necessary. Any attempt to repair or replace the flooring without our consent will void this warranty. The failure of either party to enforce any of the provisions of this warranty agreement shall not be construed as a waiver of such provision or a waiver of the right of any party thereafter to enforce each and every provision. This warranty gives you specific legal rights and you may also have other rights which vary from jurisdiction to jurisdiction. We will always respect these other rights. No implied warranties extend beyond the term of this written warranty.

WHAT YOU SHOULD DO IF ANY OF THE ABOVE LISTED PROBLEMS OCCUR
You should notify the original dealer of the defect within 30 calendar days after you know/discover the defect and within the validity period of this warranty. Your dealer can answer your questions and, if necessary, start to process a claim. If your notification takes place outside this period, our warranty will not be applicable. In order to enjoy the warranty, you are obligated to present:

• A valid proof of purchase in the form of the sales receipt for the flooring and other accessories related to the installation which may affect the installation quality such as but not limited to adhesive, molding, underlay, moisture barrier, molding, etc.
• A detailed description of the defect and/or a photograph or sample of the flooring that clearly shows the defect. Provide additional information requested by the factory to understand the root cause of the issue.
COMMERCIAL
For commercial installations, Manufacturer warrants its regular (ÿrst quality) °oor products are warranted to be free from manufacturing defects and will not wear through the printed image for the term length of the warranty coverage as set forth below in the Limited Warranty Term Length for Applicable Products and Years section, starting from the date of purchase, installed according to installation instructions and the approved application. All patch work and preparation to the sub°oor must be done and allowed to DRY prior to starting the installation. ˛the subfloor must be FLAT, SECURE, and DRY. Subfloors with high moisture trapped underneath the flooring can create pressure at the seams resulting in cupping, peaking and separation. It can take several months for the cupping, peaking and separation to become apparent after high moisture in the subfloor exists or flooding occurs, and such conditions are NOT covered under this product warranty. ˛e sub°oor must have a 6mill poly installed between the plank and sub°oor or you will void the warranty.
LIFETIME LIMITED STRUCTURAL WARRANTY
foisture will affect the floor's integrity, it is probable that, when excessive moisture accumulates in buildings or on building materials, mold (and/or) mildew growth can occur (particularly if the moisture problem remains undiscovered or unaddressed). fust maintain the proper moisture content of the subfloor/concrete and relative humidity of the room throughout the entier year. fanufacturer moisture warranty excludes damage resulting from mold and/or mildew growth due to prolonged exposure to moisture. In addition, such excessive moisture levels can cause the ends and/or sides of the product to lift/flare, cup, peak and separate due to the moisture vapor pressure from underneath. Such damage from excessive moisture levels (as outlined in the installation instructions document) are not covered by this warranty. All sources of subfloor moisture should be remedied prior to installation. This warranty is not transferable by the purchaser of the floor.

Joints compromised by improper Installation, lack of continuous climate control or obstructions creating pinch points are specifically excluded by this warranty. This Lifetime Limited Structural Warranty excludes all casualty events involving water coming in contact with your floor and failures normally covered by homeowners insurance including, but not limited to, damages caused by flooding or standing water from leaky pipes, faucets, or household appliances. Also excluded are damages caused by flooding or standing water from hydrostatic pressure or other casualty events. Any damage to the subfloor and/or surrounding structure that is caused by standing water or flooding is not covered by this warranty.

When a defective product is installed, credit applies to material only and does not include labor since it is the responsibility of the installer
to determine suitability of material prior to installation.

THIS LIFETIME LIMITED STRUCTURAL WARRANTY DOES NOT COVER:
• Damage to surrounding structure, walls, subfloor, fixtures, furniture, underlayment, moldings, trims, subfloor heating elements,or anything that is not the floor plank or tile.
• Damage resulting from mold & mildew growth due to prolonged exposure to moisture.
• Flooring that is installed outdoors.
• Squeaking noises are not covered by the warranty and note this is a floating floor so noise is allowed. Installers need to check the entire integrity of the floor system before they complete the entire project.
• Floor exposed to moisture at any time during or after installation may cause the floors to cup, lift, peak or separate. During any inspection the inspector may not find moisture at the present time but because of the structure movement of the planks, moisture or a job site condition might change the floor.
• If you don't engage the locking system correctly or cause a fracture on the locking system that is unseen during installation, the lock system will break/separate over time and the planks will come apart. It is the responsibility of the installer to ensure they engage the planks correctly without causing any fracture to the locking system.


WHAT IS NOT COVERED BY THIS LIMITED WARRANTY?
• Damage caused by fire, flooding, exposure to standing water or intentional abuse.
• Damage caused by moisture to surrounding structure, walls, subfloor, fixtures, furniture, underlayment, moldings, trims, subfloor heating elements, or anything that is not the structural integrity or dimensional stability of the floor plank or tile.
• Damage resulting from mold and mildew growth due to prolonged exposure to moisture. foisture will affect the structure of the plank or tile, when excessive moisture accumulates (and in particular remains undiscovered or unaddressed) mold and/or mildew growth can occur.
• Do not install any defective planks. If you do or don't see any defects during the installation, it is the responsibility of installer/ homeowner to call them out. fanufacturer will not be responsible for any additional labor, additional floor or any other potential cost. We always advise the homeowner to purchase 10o extra for waste. It is important and require the homeowner to stock 10o of additional stock for future repairs. If the homeowner does not, then the manufacturer/distributor will not be responsible if your floors are discontinued.
• Flooring that is installed outdoors.
• Damage caused by vacuum cleaner beater bar, rolling caster wheels, and cutting from sharp objects. When vacuuming, we recommend using the wand attachment on your vacuum.
• Indentation or damage from improper loading including high heels, spiked shoes, rolling loads, wheel chairs, electric wheel chairs, walkers with two wheels,chairs or other furniture not using floor protectors. The use of wheel chairs, and items on this list, will damage the plank flooring.
• Damage caused by abuse such as moving appliances across the floor without adequate protection. When moving appliances or heavy furniture, lay a plywood panel on your floor and 'walk' the item across it. This protects your floor from scuffing and tears.
• Loss of gloss/scratching.
• finor color, shade or texture variations between samples or printed color photography and the actual material.
• Floors that are graded 'irregular' or sold 'as is' without warranty.
• Floors that are installed in structures other than owner-occupied or tenant-occupied residences. (Except products that are noted as warranted commercial or limited commercial.)
R6.9.23 4

• Discoloration from moisture or underlayment panels after having been repaired or replaced by fanufacturer one time.
• Construction or installation-related damage - including installation defects due to installations not using the recommended
• fanufacturer products.
• Failure of the floor to adhere to the subfloor due to, for example, moisture, alkaline or vapor pressure from the subfloor.
• Inappropriate end-user activities.
• Damage due to adhesives or tape, scratches, gouges, scuffs, punctures, cuts, indentations, burns, accidents, lack of proper furniture rests, such as chair pads etc., rolling and/or non-foot traffic, or any intentional misuse of the product. Loss of finish gloss over time is consistent with normal wear & tear and is not a product flaw.
• It is normal and expected for there to be color variations due to use of natural components, exposure to UV light and/or sunlight, and age of material. Therefore, color inconsistency between samples, replacement product or illustrations and actual product is not a manufacturing flaw.
• fanufacturer makes no guarantee that fanufacturer products will match or coordinate with customer furnishings, trim, cabinetry, railings, etc.
• Noncompliance with installation instructions and maintenance guidelines as recommended by fanufacturer. fanufacturer cannot assume responsibility for the suitability of flooring material and accompanying products for each individual installation as manufacturer has no control over the installer's proper application. Should an individual piece be doubtful as to appearance or dimension the installer should not use this piece.
• Curling, cracking, warping, soiling, fading, improper maintenance or abuse caused by items such as roller skates, golf shoes, pets, and all types of wheelchairs and other heavy rolling loads.
• Floor covering installed in inappropriate locations is excluded from this warranty.
• Gloss reduction or surface scratches are not considered surface wear. Dull finish can be corrected with spot or overall recoating care systems.
• Damage to floor caused by flooring that is installed using the floating method that subsequently is heated to temperature above 140° F (60° C) or is exposed to temperatures below 32° F (0° C). This product has an attached underlayment that is not suitable for a direct glue installation.
• If your site conditions fall outside of the specified temperature range, a dry-back laminate plank installation is recommended.
• Sounds produced between the subfloor and the moisture barrier are considered a subfloor issue and are not covered under the
• product warranty.
• Squeaking noise will not be covered by the warranty and it is the responsibility of installer before they left the job site that they are no noises coming from the entire floor system. The installer should install 100 SF and test the entire floor system integrity and continue to test the floor integrity ever 250SF.

THERE ARE NO WARRANTIES BEYOND THIS EXPRESSED LIMITED WARRANTY. ALL OTHER WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED. MANUFACTURER EXCLUDES ANY LIABILITY FOR LOST PROFITS AND WILL NOT PAY ANY OTHER INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES UNDER THIS WARRANTY. BY THIS WE MEAN ANY LOSS, EXPENSE, OR DAMAGE OTHER THAN TO THE FLOORING ITSELF THAT MAY RESULT FROM A DEFECT IN THE FLOORING. NO IMPLIED WARRANTIES EXTEND BEYOND THE TERMS OF THIS WRITTEN WARRANTY. THE REMEDIES CONTAINED HEREIN ARE THE ONLY REMEDIES AVAILABLE FOR BREACH OF THIS WARRANTY.
Please note: Some jurisdictions do not allow exclusion or limitations of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. Also note: This limited warranty gives you specific legal rights, and you may also have other rights which vary from jurisdiction to jurisdiction.
LIMITED RESIDENTIAL WEAR WARRANTY
The laminate layer of the floor plank is warranted by fanufacturer not to wear through under normal use for the life of the product. Laminate layer wear-through is defined as laminate layer wear-through that exposes the core material over a minimum of 3o of the total installation. (Gloss reduction or surface scratches are not considered surface wear.) Dull finish can be corrected with spot or overall
re-coating care systems. This warranty is non-transferable and applies only to the original purchaser. This lifetime limited residential wear warranty is made subject to the following conditions:
• The floor must be installed properly and according to fanufacturer' installation instructions. Proper installation includes, but is not limited to the following:
• Concrete subfloors must be tested and confirmed dry prior to installation.
• The flooring must be used only indoors in a climate-controlled area.
• The flooring must be maintained in accordance with fanufacturer maintenance instructions.
• This limited warranty does not apply to fanufacturer moldings and trims.
• Installation of flooring that contains any manufacturing defect is not covered by this limited wear warranty.

LIGHT COMMERCIAL LIMITED WEAR WARRANTY
The laminate layer of the floor plank is warranted by fanufacturer not to wear through under normal light commercial use for a period of ten (10) years from the date of purchase. Laminate layer wear-through is defined as 100o laminate layer wear through that exposes the core material over a minimum of 3o of the total installation. (Gloss reduction or surface scratches are not considered surface wear.) Dull finish can be corrected with spot or overall re-coating care systems.
This warranty is non-transferable and applies only to the original purchaser and only if used in the following commercial areas:
• Retail: Novelty Shops/Boutiques, Product Display Areas, Showrooms, Hair Salons, Hallways
• Hotels: Conference/feeting Rooms
• fedical Offices: Waiting Rooms, Patient Rooms, Examination Rooms, Storage Rooms, Hallways
• Offices: Offices, Conference/feeting Rooms, Break Rooms
*For additional applications please call your local supplier for further information.

This 10 Year Limited Light Commercial Wear Warranty is made subject to the following conditions:
The floor must be installed properly and according to fanufacturer' installation instructions. Proper installation includes, but is not limited to the following:
• The flooring must be used only indoors in a climate controlled area.
• The flooring must be maintained in accordance with fanufacturer maintenance instructions.
• This limited warranty does not apply to fanufacturer moldings and trims.
• Installation of flooring that contains any manufacturing defect is not covered by this limited wear warranty. The 10 Year Limited Light Commercial Wear Warranty does NOT cover:
• 10 Year Limited Light Commercial Wear Warranty Damage due to adhesives or tape, scratches, gouges, scuffs, punctures, cuts, indentations, burns, accidents, lack of proper furniture rests, such as chair pads,etc., rolling and/or non- foot traffic, or any intentional misuse of the product. Loss of finish gloss over time is consistent with normal wear & tear and is not a product flaw.
• It is normal and expected for there to be color variations due to use of natural components, exposure to UV light and/or sunlight, and age of material. Therefore, color inconsistency between samples, replacement product or illustrations and actual product is not a manufacturing flaw.
• fanufacturer makes no guarantee that fanufacturer products will match or coordinate with customer furnishings, trim, cabinetry, railings, etc.
• Noncompliance with installation instructions and maintenance guidelines as recommended by fanufacturer. fanufacturer cannot assume responsibility for the suitability of flooring material and accompanying products for each individual installation as manufacturer has no control over the installer's proper application. Should an individual piece be doubtful as to appearance or dimension the installer should not use this piece.
• Cracking, warping, soiling, fading, improper maintenance or abuse caused by items such as roller skates, golf shoes, pets, or certain types of wheelchairs and other heavy rolling loads.
• Floor covering installed in inappropriate locations is excluded from this warranty.
• Gloss reduction or surface scratches are not considered surface wear. Dull finish can be corrected with spot or overall re-coating care
systems.
• Damage to floor caused by flooring that is installed using the floating method that subsequently is heated to temperature above 85° F or is exposed to temperatures below 32° F (0° C). Flooring exposed to these conditions must be installed using the glue down method in order to maintain warranty coverage.
WARRANTY LIMITATIONS
Please take notice that none of the following kinds of problems are problems arising from defects in material or workmanship, and are therefore not covered by this Product Warranty:
a) Defects arising from poor installation (this includes - damage arising from sub-floor irregularities, for example excessive unevenness, loose nails or other protrusions; visual surface defects caused by previous floor coverings that should have been removed or covered, for example ceramic or bitumastic tiles, floor-boards, cushioned laminate, or by failure in the underlayment; seams 'peaking' or opening due to use of incorrect adhesive or seaming method; edge-to-edge shade variation; discoloration arising from installation next to a source of excessive
heat); and visible trowel marks.
b) Dissatisfaction due to improper maintenance.
c) Problems arising from excessive moisture, alkali or hydrostatic pressure in substrate.
d) Problems arising from cuts, tears, gouges, burns or other damage caused by stiletto or sharp high heels (these will damage even concrete!), sharp or hot objects dropped on the floor, dragged appliances, unprotected furniture feet, damage from pets etc.
e) Damage caused by chemically reactive material, carpet crocking, dye, mold, stains, spillage, burns, gouges, scratches, indentations, floods,
R6.9.23 6

accidents, abuse or any harsh scouring pads while buffing.
f) Small differences in color and or texture between the actual material or photographic images of the material and the actual flooring
purchased.
g) Construction or installation-related damage.
h) Damage caused by inappropriate end-user activities.
i) Installation of products with adhesives other than those recommended by the fanufacturer.
j) Products may have slight color variations not detected at the factory. All products must be dry laid and examined under standard lighting conditions for color acceptance before being installed.
k) The lack of a 6 mil poly sheet moisture barrier, installed under the plank flooring, when installed over a concrete substrate.

The preceding list is not exhaustive, but is merely illustrative, of the many kinds of problems that are not due to defects in material or workmanship in the products, and are not within the coverage of this warranty. Other such problems not described on the list above are also outside the scope of this warranty. The fanufacturer will, at its option, either repair and/or replace the defective Flooring or credit the customer for the portion of the purchase price attributable to the flooring which is defective. The fanufacturer is responsible to pay for shipping and handling for any replacement, along with costs directly related to the defective flooring (e.g., pro-rated labor to remove flooring, reasonable labor to install replacement flooring, additional materials required to install replacement Flooring,). Due to the nature of the product, replacement Flooring is not guaranteed to match the original Flooring in terms of color, tone, pattern or other natural characteristics. These remedies are your sole and exclusive remedies under this warranty.
This Limited Warranty is in lieu of any other warranties, expressed or implied. Please keep your receipt or obtain it from the original retail purchaser. The fanufacturer requires the receipt in order to verify date of purchase to help resolve any problems.






































R6.9.23 7

Casabella® LAMINATE FLOOR CARE AND MAINTENANCE

♦ PLEASE REMEMBER, like any floor covering, our factory finished floors will show signs of wear over time, depending on the size and lifestyle of your family. By observing a few precautions along with setting up a regular cleaning and maintenance program, you can expect years of beauty from your floor.
♦ REGULAR CARE AND MAINTENANCE: Regular cleaning and sweeping of sand and dirt is required to maintain your new Casabella Laminate flooring surface. Sweep or vacuum regularly since built- up grit will damage the surface of the wood. The vacuum head must be a brush or felt type. Be certain the wheels of the vacuum are clean and do not damage the finish. Do not use a vacuum with a beater bar head.
♦ SPILLS: Remove all spills immediately. Use a dry or damp cloth to wipe the surface clean and dry. CAUTION: FLOOR SURFACE IS VERY SLIPPERY WHEN WET. ALLOW FLOOR TO DRY BEFORE WALKING ON SURFACE.
♦ CLEANING: Use CASABELLA® LAMINATE approved products to maintain your floor. Bona Laminate Cleaner can be used. Consult an approved dealer for instructions. ALWAYS SWEEP OR VACUUM THE FLOORS PRIOR TO USING WOOD FLOOR CLEANERS. DO NOT ALLOW EXCESS CLEANER TO REMAIN ON THE FLOORS SURFACE AS THIS MAY PERMANENTLY DAMAGE THE WOOD.
♦ DO NOT USE HARSH CLEANERS OR ABRASIVE CLEANING PRODUCTS TO CLEAN CASABELLA® FLOORING. NEVER WET-MOP, DAMP-MOP, OR CLEAN YOUR FLOOR WITH WATER OR OTHER PRODUCTS. THIS CAN SEVERELY DAMAGE THE FLOORING AND WILL VOID THE WARRANTIES. DO NOT USE FLOOR CLEANING MACHINES OR STEAM CLEANERS.
♦ DO NOT USE 2 IN 1 CLEANERS – THE USE OF THESE PRODUCTS WILL VOID THE FINISH WARRANTY AND MAY PRODUCE UNSATISFACTORY RESULTS WHEN NOT APPLIED PROPERLY. DO NOT USE OIL, SOAPS, LIQUID OR PASTE WAX PRODUCTS OR OTHER HOUSEHOLD CLEANERS THAT CONTAIN CITRUS OILS, LEMON OIL, TUNG OIL, SILICON, OR AMMONIA SINCE OUR WARRANTIES DO NOT COVER DAMAGE CAUSED BY NON-RECOMMENDED PRODUCTS. USE OF THESE AND OTHER SUCH PRODUCTS WILL HARM THE LONG-TERM PERFORMANCE OF YOUR FLOOR AND WILL VOID YOUR WARRANTY.
♦ FURNITURE:
1. NEVER SLIDE FURNITURE OR OTHER HEAVY ITEMS ACROSS FLOOR.
Always protect the floor surface when moving items across the floor. Use a dolly and protective sheets of plywood when moving heavy objects, furniture, or appliances.
2. NEVER PLACE HEAVY OBJECTS ON THE FLOOR WITHOUT “FLOOR PROTECTORS”.
3. NEVER PLACE HEAVY FURNITURE ON FLOOR FOR EXTENDED PERIODS OF TIME WITHOUT FLOOR PROTECTORS. AVOID HARD ROLLING CASTERS. USE FLOOR PROTECTOR PADS FOR
ROLLING CHAIRS. Make certain furniture casters are clean and operate properly (a minimum 1” wide vinyl surface where it comes in contact with laminate is recommended). Clean wheels periodically to remove dirt and debris.
♦ HOT ITEMS: NEVER place “HOT ITEMS” on the floor surface.
♦ PETS: Clean up pet waste immediately as it is harmful to your CASABELLA® LAMINATE. Keep pets’ nails trimmed, and paws clean and free of dirt, gravel, grease, oil, and stains.
♦ REMOVE SHOES with spiked or damaged heels before walking on floor.
♦ MAINTAIN THE PROPER RELATIVE HUMIDITY in your home between 35% - 55%. The use of a humidifier during heating seasons may help reduce shrinkage of the wood due to low humidity.

MAINTENANCE TIPS:
♦ Place outside doormats in all outside doorways to reduce dirt and moisture.
♦ Wipe up all moisture spills immediately.
♦ Clean the floor often.
♦ Do not use excessive water.
♦ Do not use unapproved cleaners, soaps, or detergents. MANY OF THESE PRODUCTS WILL DESTROY THE FINISH ON YOUR FLOOR. BE VERY CAREFUL NOT TO USE CLOTHS CONTAMINATED WITH OTHER CLEANING PRODUCTS ON YOUR FLOORS. IT WILL VOID YOUR WARRANTY.
♦ BONA HARDWOOD FLOOR CLEANER AND TERRY CLOTH MOP KIT WILL REMOVE MOST SUBSTANCES FROM YOUR FLOOR.
USE CASABELLA LAMINATE™ FLOORING APPROVED PRODUCTS FOR LONG LASTING PERFORMANCE AND BEAUTY. FAILURE TO FOLLOW THE ABOVE CARE AND MAINTENANCE TIPS WILL VOID YOUR WARRANTY.