Maple Sapling PureTech Ellenwood Vinyl Plank

Dimensions: 10mm x 7.5" x 54" - 20 mil Wear Layer
Construction: PVC-free, Rigid Core Plank - Attached Underlayment
Design: Resilient RPC
Coverage: 28.22/SQ.FT
Edge Style: GenuEdge
Finish: WetProtect®
Install Method: Uniclic® Floating
Certification: Green Guard, FloorScore
Warranty: Lifetime Residential

4 IN Transition

Quarter Round

Stair Nose

Site Requirements
PureTech is a durable floor covering, not intended as structural material. PureTech requires a clean, dry, secure subfloor that meets building codes.
The following requirements are not intended to supersede federal, state, or local building codes but, as with many other interior finish products, may require modifying existing structural components for successful installation. Owner assumes responsibility for compliance with all building codes.
PureTech is suitable for use in climate-controlled (35%—65% RH and 60°—85° F) indoor installations only and should not be installed over any floor with a sump pump or in a room with a floor drain. PureTech can be installed above, on, or below grade.
A moisture test is strongly recommended to determine if high moisture exists in the subfloor. When using a calcium chloride moisture test for concrete subfloors (ASTM F1869), values must be ≤ 5 lbs/1000ft²/24 hrs or < 80% RH with an in-situ probe (ASTM F2170).
Moisture readings of wood subfloors must be ≤ 12%.
Acceptable job site conditions, including relative humidity and subfloor moisture conditions, must be maintained throughout the lifetime of the flooring.
PureTech flooring is installed as a floating floor and requires the use of T-moldings in doorways less than 32 inches (0.81m), or if the installation changes directions through the doorway (regardless of doorway size), and in rooms 50 feet (15.24 m) or larger in length or width. Floor movement must not be constrained by glue, nails, screws, hardware, or other fixed obstructions.
This product must be installed in accordance with these installation instructions.

Site and Material Preparation
A) Remove carpet and padding. Also remove any wood flooring installed on concrete. Do not remove products unless they are asbestos-free.
B) Undercut doorframe and wallbase. Slide the flooring at least 1/4 inch underneath the doorframe and wallbase. Also, leave a concealed 3/8-inch minimum expansion space under each.
C) Remove bumps or peaks in subfloor and fill depressions with floor leveling compound to ensure no more than 3/16 inch unevenness per 10-foot span.
D) Acclimate unopened product before installation. If there is no time for acclimation, there should be no more than a difference of 25° F and 20% relative humidity between the stocking/transportation environment of the flooring and the final installation environment of the flooring.
E) Clean debris from subfloor before installation.
F) For concrete subfloors, install vapor barrier with overlapped seams of 8 inches or more.

Flooring Installation
1) Inspect each plank. Floor should be installed blending planks from several cartons at the same time to ensure good color and shade mixture throughout the installation.
2) For the first row along straight walls, remove the tongue on all long-side joints and on the short side of the first plank only.
3) For uneven walls, trace contour on tongue side of plank and cut.
4) Assemble the first row tongue side toward wall. Insert the end tongue into the end groove and rotate downward to assemble. Keep the planks aligned and the joints closed.
5) Two spacers thick side to thick side equal 3/8 inch.
6) Provide a 3/8 inch space for expansion on all sides. First piece must be at least 8 inches long. Start new rows with pieces trimmed from previous row. Ensure at least a 12-inch end joint offset.
7) At a slight angle, insert the tongue of plank 2 into the groove of plank 1 until the edges meet, and then rotate downward until the joints lock.
8) Join the short end of the plank first. There will be a gap on the long-side joints when the plank is rotated downward.
9) Raise the outside edge of the plank, as well as the first plank in row 2, upward approximately 1 inch. Maintain this angle as you push the plank in until the plank edges meet. Rotate the plank downward until the joint locks. Repeat these steps to complete the installation.
Installation Tip: Place a carton of planks across the end of the row being installed to keep installed planks in place during installation.
10) Alternate Tap Method: Align the tongues into the grooves of the long and short sides of the planks. Install the long side first by placing a tapping block no closer than 8 inches from either end and tap lightly along the long side until the joint is closed tightly. Then tap the end into a locked position using the tapping block Note: Uneven tapping or use of excessive force may damage the joint.
11) Ensure there will be a 3/8 inch gap (after the joint is closed) between the plank and the wall for expansion.
12) For the last row, align the plank to be used on top of the second-to-last row. Using a full-width plank as a spacer, trace wall contour and cut plank.
13) For the last row, install the long-side tongue into the groove with the end joint aligned. Using a pull bar and hammer, work evenly along the length of the plank and lightly tap the joint closed.
14) After tapping the long side joint closed, tap the short side closed using a tapping block or a pull bar.
Installation Under Doorway Casing
15) Slide plank under precut doorframe.
16) Tap the long-side joint closed first. Then tap the end joint closed.

Installation Around Fixed Objects (Such as Pipes)
17) Allow a 3/8 inch expansion space around pipes or other fixed objects.
Finishing the Installation
18) Remove all spacers.
19) The entire perimeter of the installation should be sealed with the WetProtect® molding system in accordance with the installation instructions.
For sections where the WetProtect molding system cannot be used, seal the perimeter with 100% silicone sealant, as follows (DO NOT use acrylic sealant):
• First, fill all expansion spaces with 3/8 inch compressible PE foam backer rod and cover with silicone sealant.
• Prior to installing the moldings, apply silicone sealant to the portion of the molding or transition that will directly contact the flooring surface.
• Install moldings and immediately wipe away any excess silicone sealant.
• Apply silicone at connections to doorframes or any other fixed objects.
Note: For complete WetProtect coverage, perimeter must be sealed. See warranty for details.

Care and Cleaning
Place felt floor protectors under legs of moveable furniture. Chair casters should be rubber — not plastic or metal. Place walk-off mats at entrances. Dust mop as primary cleaning method. Occasionally wet mop with water only, using a well-wrung-out mop. DO NOT pour liquid directly on floor or use an excessively wet mop that will puddle or leave moisture standing on the floor. If needed, use a solution of 1 cup of vinegar per gallon of water OR 1/3-cup non-sudsing ammonia per gallon of water. DO NOT use detergents, abrasive cleaners, soaps, waxes, or polishes. A residential steam mop may be used provided the steam is applied to a microfiber pad and not applied directly to the floor. Make sure to set the temperature of the steam mop to the appropriate setting for PureTech floors, or to the lowest setting. Steam mop in the length direction of the planks only. Use correct hard surface vacuum tools. DO NOT use rotating beater bars, floor scrubbers, jet mops, or similar products. Wipe up spills immediately. DO NOT allow topical moisture to remain on the floor longer than the time specified in the product warranty.

WARNING: DRILLING, SAWING, SANDING OR MACHINING WOOD PRODUCTS CAN EXPOSE YOU TO WOOD DUST, A SUBSTANCE KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER. AVOID INHALING WOOD DUST OR USE A DUST MASK OR OTHER SAFEGUARDS FOR PERSONAL PROTECTION. FOR MORE INFORMATION, GO TO WWW.P65WARNINGS.CA.GOV/WOOD.

IMPORTANT HEALTH NOTICE FOR MINNESOTA RESIDENTS ONLY: THESE BUILDING MATERIALS EMIT FORMALDEHYDE. EYE, NOSE, AND THROAT IRRITATION, HEADACHE, NAUSEA AND A VARIETY OF ASTHMA-LIKE SYMPTOMS, INCLUDING SHORTNESS OF BREATH, HAVE BEEN REPORTED AS A RESULT OF FORMALDEHYDE EXPOSURE. ELDERLY PERSONS AND YOUNG CHILDREN, AS WELL AS ANYONE WITH A HISTORY OF ASTHMA, ALLERGIES, OR LUNG PROBLEMS, MAY BE AT GREATER RISK. RESEARCH IS CONTINUING ON THE POSSIBLE LONG-TERM EFFECTS OF EXPOSURE TO FORMALDEHYDE. REDUCED VENTILATION MAY ALLOW FORMALDEHYDE AND OTHER CONTAMINANTS TO ACCUMULATE IN THE INDOOR AIR. HIGH INDOOR TEMPERATURES AND HUMIDITY RAISE FORMALDEHYDE LEVELS. WHEN A HOME IS TO BE LOCATED IN AREAS SUBJECT TO EXTREME SUMMER TEMPERATURES, AN AIR-CONDITIONING SYSTEM CAN BE USED TO CONTROL INDOOR TEMPERATURE LEVELS. OTHER MEANS OF CONTROLLED MECHANICAL VENTILATION CAN BE USED TO REDUCE LEVELS OF FORMALDEHYDE AND OTHER INDOOR AIR CONTAMINANTS. IF YOU HAVE ANY QUESTIONS REGARDING THE HEALTH EFFECTS OF FORMALDEHYDE, CONSULT YOUR DOCTOR OR CALL LOCAL HEALTH DEPARTMENT.

MOHAWK LIMITED
RESIDENTIAL WARRANTIES
Manufacturing Defect Warranty (All PureTech Products)
Mohawk warrants to the original buyer that the flooring will be free of defects in material and/or workmanship in accordance with the terms of this warranty for as long as the buyer owns the home.

Terms and Conditions
• This limited warranty only covers the flooring under normal residential use when Mohawk installation and maintenance instructions are followed properly.
• This warranty only applies to inherent defects that were not visible before or during the installation of the flooring.
• Flooring planks or accessories must be checked carefully for material defects before and during installation under sufficient lighting. Installation indicates acceptance of quality.
Exclusions
• These limited warranties do not cover damage to the flooring that occurs during shipment or installation.
• Installation of flooring that contains any obvious or visible manufacturing defect is not covered by these limited warranties.
• Color and gloss differences resulting from material added to an existing installation at a later date or from non-warranty repairs are excluded from coverage.
• These limited warranties do not apply to flooring that has been subjected to abnormal use or conditions or abused in any way, which includes, but is not limited to, moisture damage from plumbing, storms, or flooding;
damage from smoke, fire or other casualty events; damage caused by negligence; improper alterations of the original manufactured product; damage from use of the flooring that is unreasonable considering the normal and expected uses of flooring in a residential environment; or damage of a mechanical nature.
• This warranty only covers finish defects when defective flooring exceeds 10% of the total square footage of installed flooring.

Wear Resistance Warranty (All PureTech Products)
As a result of normal use, the protective layer will not wear through to the decorative layer.
Terms and Conditions
• Gloss change is not considered surface wear.
• In beveled-edge products, this wear resistance warranty does not include wear along the edges of the planks less than 3/16” (5 mm) from the edge.
• Wear of the PureTech or design layer must be readily visible, covering at least one square inch.
• Chair pads or mats must be used under caster chairs.
General Stain Warranty (All PureTech Products)
Mohawk warrants to the original buyer that the flooring will not stain under normal household use for the specified duration.
Terms and Conditions
• This warranty does not apply to stains as a result of chemical or industrial products other than recommended cleaning products.
• Topical spills should be removed promptly using a clean, dry or damp cloth. If additional cleaning is needed, use a Mohawk recommended product and a microfiber cloth.
• This warranty excludes pet stains.
Fade Resistance Warranty (All PureTech Products)
The flooring will not fade from exposure to sunlight or artificial light for the specified duration.

WET WARRANTY
WetProtect® Warranty (All PureTech Products)
WetProtect is a no-exclusions wet warranty that covers damage from all common household spills, domestic household pet accidents, and damp and wet mopping. In addition, the coverage includes damage to both the flooring and subfloor from topical moisture for the life
of the product.
Terms and Conditions
• Subfloor damage is defined as visible damage to the surface of a concrete or wood subfloor, including mold or mildew growth, rot or decay caused by topical moisture leaking through the joint system.
• In all cases, subfloor damage must be the result of topical moisture leaking through a properly installed joint.
• See General Wet Warranty Terms and Conditions for additional information regarding this WetProtect Warranty.

Steam Mop Warranty (All PureTech Products)
A residential steam mop may be used, provided the steam is applied to a microfiber pad and not applied directly to the floor.
• Make sure to set the temperature of the steam mop to the appropriate setting for PureTech floors or to the lowest setting.
• Steam mop in the length direction of the planks only.
General Wet Warranty Terms and Conditions
Unless otherwise specified, topical spills refer to normal household substances. All spills should be removed promptly using a clean, dry or damp cloth. If additional cleaning is necessary, use Mohawk recommended products and a microfiber cloth.
• These warranties are contingent on proper care and maintenance. Please refer to Mohawk’s Care and Maintenance section for full instructions.
• These warranties are contingent on proper installation. Please refer to Mohawk’s PureTech Installation Guide for full instructions.
• Complete waterproof coverage requires the perimeter of the floor to be sealed in accordance with the products installation instructions. Waterproof and WetProtect warranties do not apply to damage at an unsealed perimeter, including but not limited to: leaks, spills, pet urine, wet mopping, or steam mopping.
 

Joint Integrity Warranty (All PureTech
Products)

The flooring joints will remain secure under normal use.

• Responsibility under this warranty only applies to flooring defects that were not visible before or during the installation of the product.
• This warranty only applies to open joints greater than 0.015 inch (0.381 mm).

PET PROTECTION
Mohawk All Pet® (All PureTech Products)
All Pet Stain Protection covers all pets and all accidents for the specified duration. The flooring will resist staining from vomit, urine, and feces of all domestic pets. Please refer to the attached Warranty Chart for precise duration of coverage, listed by product line.
Pet Scratch Protection Warranty (All PureTech Products)
Our Pet Scratch Protection Warranty is built on cutting-edge scratch technology, specifically engineered to withstand the playful paws of your beloved pets. These products have been tested and guaranteed to resist pet scratches throughout the entire warranty period. This promise is supported by a hassle-free warranty with no hidden clauses or long list of exclusions. The terms of this warranty are simple. If your domestic pet leaves a scratch on your protected flooring, we will replace the affected planks without hesitation. A "pet scratch" is simply defined as any loss of the design layer, visible from standing height under typical household lighting, which was caused by your pet's nails.
While we stand by the exceptional durability of our floors, it is essential to acknowledge that no surface can be deemed completely impervious to scratches. We advise taking appropriate precautions when dealing with heavy or sharp objects, as they can inflict severe damage to any flooring if not handled with care. For a comprehensive guide on prevent- ing non-pet-related damage, please refer to the Care and Maintenance section of this warranty.

Commercial Warranties
Limited Light Commercial Warranty (All PureTech Products) When installed properly within a light commercial environment, the flooring is warranted against manufacturing defects, wear, and staining in accordance with all previously stated terms and conditions. Refer to relevant sections for details, and see the Warranty Chart for specified Commercial Warranty duration.

Light Commercial Fade Warranty (All PureTech Products)
The flooring will not fade from exposure to sunlight or artificial light.
Terms and Conditions
• These commercial warranties apply only to the original purchaser.
• These commercial warranties apply only if used in one of the following areas.
• Rolling traffic or heavy traffic is excluded from these warranties. Chair pads must be used under all caster wheel chairs.
All areas must be assessed prior to installation of flooring to determine if other surface measures need to be taken or conditions addressed, including, but not limited to, requirements for static control, state health and building codes, slip resistance, high-impact traffic, and moisture/ water exposure. Other than the specific warranty identified above, Mohawk provides no additional warranties and Mohawk does not warrant that any of the uses identified above are in compliance with
any applicable building, health, inspection, and/or other municipal regulation or codes. Mohawk is not responsible for usage that is not in compliance with any regulation or code. Proper assessment of location and usage must be applied. Contact your Mohawk representative for questions on performance in specific locations.

Light Commercial Defined
Mohawk warrants only first quality products for recommended light commercial use such as those outlined in the following Light Commercial Application Chart. Products will perform as warranted for the stated warranty period when installed in accordance with the PureTech Installation Guide over approved substrates and underlayments.
• Light commercial use is defined as use in environments that do not experience normal to heavy commercial traffic such as those outlined in the Light Commercial Application Chart below. PLEASE NOTE, warranty exclusions apply with respect to casters and other rolling loads due to the unusual characteristics of this type of wheeled traffic.
• The intended applications include privately owned in-house businesses, such as daycare centers, doctors'/dentists' offices, and barber/beauty shops. For questions as to the type of use that is considered “light commercial”, please contact Mohawk Technical Services prior to purchase
and installation.
• Mohawk is not responsible for usage that is not in compliance with any regulation or code.

Light Commercial Application Chart
Retail Entryway Sales Floor Showroom Checkout Breakroom
Dressing Room Office
Storage Room Offices Entryway Lobby Hallway Office
Conference Room Meeting Room Breakroom Multi-family Housing
Entryway Lobby Hallway
Common Area Office
Storage Room Individual Housing Unit
Doctor’s Offices
Entryway Lobby Hallway Waiting Room
Nurses’ Station Office Breakroom Storage Room Education Entryway Lobby Hallway Office Classroom Storage Room
Residence Hall Common Area Hotels Entryway Lobby Hallway Guest Room
Conference Room Meeting Room Kitchenette Lounge
Office
Restaurants Entryway Lobby Hallway Office

GENERAL TERMS AND CONDITIONS
These limited warranties are subject to the following conditions:
• These limited warranties apply only to the person stated as the buyer on the purchase document(s).
• These limited warranties apply only to first quality product purchases made after the edition date of this document.
• These limited warranties do not apply to moldings.
• The product must be properly installed according to the Mohawk written Installation Instructions, available from the retailer or on Mohawkflooring.com
• Flooring installed with visible defects is not covered by these limited warranties.
• The limited warranties do not apply to flooring that has been reinstalled in a second location.
• The product must be installed in an indoor, continuously climate-controlled, private residence or light commercial environment as indicated by the Warranty Chart.
• Damage that occurs during shipment or installation is not covered.
The flooring must be maintained in accordance with Mohawk's written Care and Maintenance instructions. Please refer to Mohawk’s Care and Maintenance section for full instructions.
• Damage resulting from excessively wet maintenance or from using detergents, abrasive cleaners, soaps, waxes, or polishes is not covered.
• Damage resulting from the use of rotating beater bars, floor scrubbers, jet mops, steam mops, buffers, or similar products is not covered.
• Damage resulting from improper or inadequate maintenance or accidents is not covered, including, but not limited to, damage caused impact, gouging, or cutting.
• Scratching during and after installation is not covered by these limited warranties.
The flooring is designed for normal residential or light commercial use, as specified in the Warranty Chart.
• Damage caused by events beyond everyday household use is not covered by these limited warranties, including, but not limited to, flooding, standing water, leaking pipes, mechanical failures, or appliance leaks.

Although our floors are designed with easy care in mind, all floors require routine care and preventative maintenance for sustained beauty and performance. The recommendations in this section are provided in accordance with guidelines required to maintain the coverage of these limited warranties and will prolong the life of the installed flooring. For full details, refer to the Care and Maintenance section for full instructions.

Preventative Maintenance
Exterior Mats
• Place exterior mats outside all exterior entrances.
• Exterior mats should be constructed of dual fibers: soft fibers capable of absorbing moisture and coarse fibers to remove dirt and grime from shoe soles.
• To allow time for cleaning, purchase two sets of exterior mats. Place one set at all exterior entrances to reduce the amount of dirt, grit, and moisture tracked into the home. When it’s time for cleaning, remove the soiled set and immediately replace with the fresh set.
• Cleaning mats routinely prevents them from becoming a soil source.
Interior Mats
• Place interior mats inside all exterior entrances to capture any residual dirt, grit, or moisture missed by exterior mats.
• Interior mats should be constructed of an absorbent fiber with a breathable, nonstaining back.
• Remember to routinely clean both sides of interior mats so they don’t become a secondary source of soil, and also clean underneath to prevent soil and grit from becoming trapped and dulling the finish of the flooring.
• Do not use rubber mats which may stain the floor or trap moisture underneath the mat.

Furniture
• Use nonstaining felt or plastic floor protectors at least one inch in diameter under furniture and covering the part resting on the flooring.
• Chair casters should be rubber, not plastic or metal. Chair pads should be used under chair casters.
• Routinely clean casters to remove grit.
• Lay plywood over the floor to avoid dents and gouges, and use a furniture dolly when moving heavy appliances and furniture.
Other Preventative Measures
• Keep pet nails trimmed to minimize scratches.
• Protect flooring from spiked heels, athletic shoes, or shoes in need of repair.
• Routinely clean vacuum wheels, brush, and head, and periodically inspect for foreign objects.
• Close window treatments during hours of direct sunlight and minimize excessive lighting whenever possible to protect floor.
• Exercise caution when placing area rugs over floors with radiant heating. Rugs may increase flooring temperatures beyond recommended levels and void the warranty.

Routine Care
The amount of daily usage will determine how often cleaning is required.
Day-To-Day Cleaning
• Dust mop, sweep, and/or vacuum the floor regularly to remove any particles that could scratch the floor.
• WARNING: Vacuums with a beater bar or power rotary brush head should never be used on PureTech flooring.
• Use vacuum tools designed for hard surfaces.
• Use a microfiber mop for dust mopping. Pay close attention to the mop head. Once soiled, replace with a fresh one. Launder soiled mop heads without fabric softener. Fabric softener residue may cause streaking on the floors.
Occasional Cleaning
• Never wet mop flooring unless it is covered by the WetProtect Warranty.* If flooring product allows, occasionally wet mop with water only, using a well-wrung-out mop.
• If needed, use 1 cup of vinegar per gallon of water OR 1/3 cup non-sudsing ammonia per gallon of water.
• Never steam mop flooring unless it is covered by the Steam Mop Warranty.*
• Flood mopping is never recommended since mop water may damage flooring and leave spots.
• Do not pour liquid directly on the floor or use an excessively wet mop.
• Do not allow liquid to puddle or leave moisture standing on the floor.
• Allow floor to dry completely before replacing interior mats. NOTE: *See Wet Warranty section for details.
Cleaning Spills
• Remove spills promptly. Do not allow topical moisture to remain on the floor.
• Immediately use an absorbent cloth to remove as much of the liquid as possible.
• Mist a clean microfiber cloth with a Mohawk recommended cleaner, if needed, and rub the area, working from the outside of the area toward the center.
• Take care to wipe the surface thoroughly.
• To reduce spotting, do not allow liquids to stand or remain on the surface of the flooring.

Spot Removal
• Immediately use a microfiber cloth and a Mohawk- recommended cleaner, if needed, working from the outside of the stain toward the center.
• Take care to wipe the surface thoroughly.
• To reduce spotting, do not allow liquids to stand or remain on the surface of the flooring.
Products and Tools to Avoid
• Do not use oil soaps, wax, detergents, abrasive cleaners, polishes, surfactant, or other household products to clean the floor.
• Vacuums with beater bar or power rotary brush head should never be used on PureTech flooring.
• Never use power scrubbers to clean floor.